Safety Precautions; Authorised Personnel - golmar ART 4 LITE/G2+ Guía Rápida

ART 4 LITE/G2+ MONITOR

SAFETY PRECAUTIONS

Always disconnect the power supply
- before installing or making modifications to the device.
.
- The fitting and handling of these devices must be carried out by
.
- The wiring must run at least 40 cm. away from any other wiring.
- Do not overtighten the screws on the connector.
- Install the monitor in a dry protected location free from the risk of dripping or splashing water.
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- Before connecting the device to the mains, check the connections between the door panel, power
supply, distributors and monitors.
- Always follow the instructions contained in this manual.
( ) CHARACTERISTICS
*
- Hands-free monitor.
- 4,3 " TFT c olo r u screen .
.
- Function push buttons for access and selection of menu function.
- Monitor with simple installation (non-polarised 2 wires bus)
.User
- User menu .
.
- Installer menu .
.
- Image and communication settings menu .
.
- Output auxiliary call repeater (max. 50mA/12V ).
.
- "HZ" input for calls from apartment front door.
.
- Push buttons for door release 1 and 2.
.
- Notification l eds.
.
- Configuration switches to assign the call address
- Function codes to define whether the monitor is master or slave (default: master).
( ) SYSTEM OPERATION
*
- To make a call, the visitor must press the button of the apartment; an audible sound indicates that the call
is being made and door panel LED will turn on. If vocal synthesis is enabled, a 'Call is in progress'
message appears indicating that a call is being made. At this moment, the apartment's monitors receive
the call. If another apartment is called by mistake, press the button for the correct apartment and the first
call will be cancelled.
.
- Upon receiving the call, the image will appear on the screen of the master monitor (and slave 1, if it
exists) without the visitor knowing and icon
image from slave monitors 2 or 3, press one of the buttons of the monitor to display the image
call is not answered within 45 seconds, door panel
.
- To establish communication, press the button below
panel LED will turn off and the led will turn on
front, make sure that the hearing aid is between 15 and 25 cm away from the monitor to ensure
maximum audio quality during communication with the door panel.
.
- Co mmunication will last for 90 seconds or until
is pressed. When communication ends, door panel
vocal synthesis is enabled, a 'Communication is finished' message will indicate that the call is over.
.
- To open door or of the door panel , press the
1 2
screen during the call or communication processes: one press will activate the lock release for
seconds and door panel LED will also turn on for seconds. If vocal synthesis is enabled, a 'Door
open' message will be indicated on the door panel.
.
- Detailed operation and configuration of the monitor
( ) INSTALA TION OF THE MONITOR
*
( )
* For more information, see "TART 4 LITE /G2+
https://doc.golmar.es/search/manual/50122623

authorised personnel

.
.
dc
(1 to 128) and end of line.
displayed on the screen will blink green. To view the
LED will turn off and the system will become free.
off-the-hook icon sh wn on o the screen. Door
. If the monitor is a n 'ART 4H LITE' with icon
the button below on-the-hook icon shown on the screen
LED will turn off and the system will become free. If
button below the corresponding icon displayed
3
, see "TART /G2+" user manual 4 .
user manual (code 50122 623 )".
2
ART 4 LITE/G2+
( ) DESCRIP TION MONITOR
*
A
B
C
K
I
SA
GND
J
HZ
HZ
BUS
BUS
128
codes
SA
DIP 1 to 7
Monitor
GND
address
HZ
DIP 8
HZ
EOL
resistor
BUS
OFF = 0
ON = 1
BUS
K
( )
*
Monitor address (code) setup:
Dip1 Dip7: - Sets the monitor address (addresses to
The switches set to OFF have a zero value. The values of the switches set to ON are shown in the table below. The
monitor code is the sum of the values of the switches set to ON.
Important: Apartment 1 (Dip1 to ON & Dip2-Dip to OFF).
Important: Apartment 2 (Dip1 - Dip to OFF). 1 8
Dip8: This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable ends.
Deactivate it only in intermediate monitors.
Dip 8 a ON
. If the
ON
1 2 3 4 5 6 7 8
on the
Not : e To define whether the monitor is master or slave, entering the corresponding "Special code":
"0550" Master (factory default),
Dip1 to Dip : 7 These assign the address of the monitor to call button on the door panel.
Switches - must remain in the OFF position. 2 7
Apartment 1
on the
ON
3
1 2 3 4 5 6 7 8
is
Dip8: This activates the end-of-line resistance in the ON position. Activate it in monitor where the bus cable ends.
Deactivate it only in intermediate monitors.
Dip 8 a ON
ON
1 2 3 4 5 6 7 8
( )
* For more information, see
https://doc.golmar.es/search/manual/50122623
EN
MONITOR
A. Speaker .
B. Function buttons, access and selection of menu functions.
The function of each button is shown on the monitor screen with an
icon located just above each button (see "TART 4 LITE/G2+"
manual).
D
Press to access 'Doctor mode' function (standby monitor):
*
- With the special code '0441' (Doctor mode) already entered (see
special codes i n manual "TART 4 LITE/G2+"
for 1 sec. to activate/ deactivate the function.
- The push button led will blink in white color if the function
E
'Doctor mode' is activated and it will turn off if the function is
deactivated.
F
C.
Monitor status LED:
G
Yellow ON: Standby without notification.
Red ON: "Do not disturb" Mode a tivated.
H
D. 4.3" TFT colour screen.
E. Golmar use.
K
F. Microphone .
G. Communication with hearing aids
Set the hearing aid switch to the T position.
H. Raised dots for the visually impaired
In call /communication :
MADE IN CHINA
Above this raised dot is the 'Start/ nd communication' button.
Above these raised dots is the 'Door opening' button.
I. Configuration switches.
J. Installation terminals .
K
K. Wall mounting connector fixing (x4).
Building / Villa (Nexa Door Panel)
1 1 8 2 ).
Table of values
7
Switch number: 1 2 3 4 5
7
Value when ON :1 2 4 8 16 32 64
Dip 8 a OFF
ON
1 2 3 4 5 6 7 8
"0551" Slave 1, "0552" Slave or "0553" Slave . 2 3
Villa (Soul Door Panel)
*
Not : e To define whether the monitor is master or slave, entering
the corresponding "Special code": "0550" Master (factory
default), "0551" Slave 1, "0552" Slave or "0553" Slave . 2
Dip 8 a OFF
ON
1 2 3 4 5 6 7 8
"TART 4 LITE /G2+ user manual (code 50122
3
), press the button
c
( ART 4H LITE G2+ / ) .
people.
E
ON
6 7
1 2 3 4 5 6 7 8
Example: 0+ 0+4+0+ 16+ 0+0 = 20
*
Kit Soul / Art Lite 4
3
Manual
623 )".
EN