S&P HTB-75N Manual De Instalacion E Instrucciones De Uso página 12

IMPORTANT NOTE : The warnings,safeguards and instructions given in this manual are not
exhaustive and do not nessecarily cover all eventualities. It must be understood that common sense,
caution and care are factors which cannot be built into any product. These factors must be supplied
by the person(s) caring for and operating the unit.
UNPACKING INSTRUCTIONS
UNPACKING INSTRUCTIONS
Before assembling the ceiling fan, remove all parts from the shipping carton and check them against
Before assembling the ceiling fan, remove all parts from the shipping carton and check them against
the parts listed below (Fig. 1 ) :
the parts listed below (Fig. 1 ) :
A- Support plate (1 pc.)
A- Support plate (1 pc.)
B- Motor assembly and support (1 pc.)
B- Motor assembly and support (1 pc.)
C- Blades (3 pcs.)
C- Blades (3 pcs.)
D- Blade fitting screw (6 pcs.)
D- Blade fitting screw (6 pcs.)
E- Washers (6 pcs.)
E- Washers (6 pcs.)
F- Speed regulator (1 pc.)
F- Speed regulator (1 pc.)
G- Wall plugs (2 pcs.)
G- Wall plugs (2 pcs.)
H- Screws (2 pcs.)
H- Screws (2 pcs.)
I- Washers ( 2 pcs.)
I- Washers ( 2 pcs.)
J- Felt washers ( 3pcs )
J- Felt washers ( 3pcs )
Instructions Manual
Instructions Manual
INSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION
FITTING THE FAN TO THE CEILING
FITTING THE FAN TO THE CEILING
Important: To avoid the possibility of accidents caused by the fan, which could imply legal
Important: To avoid the possibility of accidents caused by the fan, which could imply legal
responsibilities for the installer, compliance with each of the following instructions is essential.
responsibilities for the installer, compliance with each of the following instructions is essential.
Ensure that the distance between the lowest point of the fan, once installed, and the floor is at
Ensure that the distance between the lowest point of the fan, once installed, and the floor is at
least 2.3 meters.
least 2.3 meters.
Check that the means of fitting the fan to the ceiling is capable of supporting the weight of the fan
Check that the means of fitting the fan to the ceiling is capable of supporting the weight of the fan
Check that the means of fitting the fan to the ceiling is capable of supporting the weight of the fan
when in operation. (HTB 75 N / HTB 90 N Minimum 25 Kg. - HTB 150 N Minimum 40 Kg.).
when in operation.
when in operation. (HTB 75 N / HTB 90 N Minimum 25 Kg. - HTB 150 N Minimum 40 Kg.).
HTB-75N / HTB-90N mínimum 25 Kg.
Fitting to a concrete ceiling HTB-140 / HTB-150N mínimum 40 Kg.
Fitting to a concrete ceiling
To ensure correct installation, drill four holes of the same diameter as the wall plugs (G) in the To ensure correct installation, drill four holes of the same diameter as the wall plugs (G) in the con-
To ensure correct installation, drill four holes of the same diameter as the wall plugs (G) in the
concrete ceiling. Insert the plugs supplied and fix the support plate (A) using the four screws (H) crete ceiling. Insert the plugs supplied and fix the support plate (A) using the four screws (H) and
concrete ceiling. Insert the plugs supplied and fix the support plate (A) using the four screws (H)
washers (I) provided. (Fig.2).
and washers (I) provided. (Fig.2).
and washers (I) provided. (Fig.2).
Fitting to a false ceiling
Fitting to a false ceiling
Make a hole in the false ceiling that is large enough to allow the introduction of a rigid, wooden or
Make a hole in the false ceiling that is large enough to allow the introduction of a rigid, wooden or
metal cross beam. This should be as long as possible and under no circumstances less than 25cm.
metal cross beam. This should be as long as possible and under no circumstances less than 25cm.
in length, to allow the best distribution of the weight of the fan.
in length, to allow the best distribution of the weight of the fan.
Without reducing its ability to support the fan, make a small groove at the centre of the crossbeam,
Without reducing its ability to support the fan, make a small groove at the centre of the crossbeam,
then locate the beam so that its centre coincides with the hole in the ceiling.
then locate the beam so that its centre coincides with the hole in the ceiling.
Join the support plate (A) to the crossbeam using galvanised metal wire of at least 2.5mm in diameter.
Join the support plate (A) to the crossbeam using galvanised metal wire of at least 2.5mm in diameter.
Passing the wire through the grooves in the plate, wind it around the crossbeam and back through
Passing the wire through the grooves in the plate, wind it around the crossbeam and back through
the plate a minimum of six times, so that at least some of the turns pass through the groove in the
the plate a minimum of six times, so that at least some of the turns pass through the groove in the
crossbeam. Secure the wire by twisting it around itself several times.
crossbeam. Secure the wire by twisting it around itself several times.
Ensure that the ceiling is able to support the weight of the fan when in operation (minimum 25/40
9
12