Maintenance Section; Torque Adjustment - Ingersoll Rand 380P Manual De Funcionamiento Y Mantenimiento

Llaves de impulso de doble paleta
Ocultar thumbs Ver también para 380P:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Always wear eye protection when operating or
performing maintenance on this tool.
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool or before performing any
maintenance on this tool.
LUBRICATION
Oil:
Ingersoll–Rand No. 50 Oil.
Grease:
Ingersoll–Rand No.67 Grease.
Fluid:
Use only Ingersoll–Rand Fluid Part Number
EQ106S–400–1.
After each 20 000 cycles, or as experience indicates,
drain and refill the Impulse Unit Drive Assembly (36) as
instructed in this manual using the Fluid Replacement Kit
(Part No. EQ106S–K400). Lubricate the hex drive and the
output shaft before assembly.
We recommend the use of an air line lubricator in the air
supply line. Attach the unit as close to the tool as practi-
cal. Where the lubricator cannot be permanently mounted,
we recommend using an Ingersoll–Rand No. L01–02–000
Lubricator. For permanent installations, we recommend
using an Ingersoll–Rand C22–03–G00 Filter–Lubricator–
Regulator Unit. These units have 1/4" pipe tap inlet and
outlet. The L01–02–000 has .25 oz. (7.5 cc) capacity; the
C22–03–G00 has 5 oz. (150 cc) capacity.

TORQUE ADJUSTMENT

To adjust the torque on these Twin Blade Impulse
Wrenches, proceed as follows:
1. Remove the Adjustment Hole Plug (69).
2. Rotate the Drive Shaft (50) until the Torque Adjust-
ment Screw (37) is visible in the opening.
3. Using a 1.5 mm hex wrench, rotate the Adjustment
Screw clockwise to increase the torque output and
counterclockwise to decrease the torque output.
Do not rotate the Oil Plug (58).
Make all final adjustments at the job
4. Replace the Adjustment Hole Plug.
CHANGING THE MECHANISM FLUID
To change the Mechanism Fluid in the Impulse Mecha-
nism, proceed as follows:
1. For model 380PQ1, use a pointed probe to to push
the Spring Seat (75) against the Retaining Sleeve
Spring (74). While the Spring is compressed, use an-
other pointed probe or thin blade screwdriver to re-
move the Retaining Ring (76). Lift the Spring Seat,
Spring and Bit Retaining Sleeve (73) off the Drive
Shaft (50) and remove the Bit Retaining Ball (72).
2.
Remove the Rubber Housing Boot (77).
3.
Using copper–covered vise jaws, carefully grasp the
flats of the Mechanism Cover (67) with the output
end of the Drive Shaft downward.

MAINTENANCE SECTION

4.
5.
6.
7. Using the special Tee Wrench furnished in the Tool
8. With the oil plug opening downward over a container,
9.
10. Submerge the fill opening in the remainder of the
17
Using an adjustable wrench, unscrew the the Motor
Housing Assembly (1) from the Mechanism Cover.
This is a left–hand thread, rotate the Motor Housing
clockwise to remove it. (Refer to Dwg. TPD1264)
CLOCKWISE TO LOOSEN
Lift the assembled motor off the Mechanism Cover
and pull the mechanism assembly out of the Cover.
Using a 1.5 mm hex wrench, rotate the Torque Ad-
justment Screw (37) clockwise until the Screw stops.
Rotate the Screw counterclockwise until it stops or
makes six complete revolutions.
Kit (Part No. 180PQ–99), remove the Oil Plug (58)
and Oil Plug Seal (59).
rotate the Drive Shaft to purge the fluid from the
mechanism.
Using the syringe and fluid from the Fluid Replace-
ment Kit (Part No. EQ106S–K400), fill the mecha-
nism with the fluid furnished in the Kit. (Refer to
Dwg. TPD1265)
DO NOT SUBSTITUTE ANY OTHER FLUID.
Failure to use the fluid provided could damage the
tool, increase maintenance and decrease perfor-
mance. Use only clean fluid in these tools.
fluid, and using a wrench, rotate the Drive Shaft to
purge any remaining air from the system.
(Dwg. TPD1264)
(Dwg. TPD1265)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

380pq1

Tabla de contenido