General Safety Instructions - Global Industrial 293018 Manual Del Usuario

Please read and save these instructions. Read carefully before
attempting to assemble, install, operate or maintain the
product described. Do not use the fan if any part is damaged
or missing. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result
in personal injury and/or property damage!
Retain instructions for future reference.
To reduce the risk of fire or electric shock, do not use
this fan with any solid state speed control device. This
fan must be grounded, when using a plug cable, must
be a three-pin plug. This fan is suitable for wet
location. When Installed In A GFCI Protected Branch
Circuit.The fan is a double voltage device and it must
be wired and grounded according to the wiring
diagram.If the plug does not fit into the outlet, contact
a qualified electrician.
Do not attempt to bypass this safety feature.
NOTE: Air circulator is not to be used in unattended areas.
1. Ensure that the power source conforms to the electrical
requirements of the fan.
2. Installed in accordance with the United States National Electrical
Code (NEC) and all applicable local codes and ordinances. This
work must be done by a qualified electrician, using copper wire
only.
3. For the power cord connection, the appropriate wire Type SJTW
should be used.The specifications are not lower than
NO.18AWG,rated minimum 300 V, 80C.Cord length minimum
1.5 m and 1.8 m long for USL and CNL respectively, maximum
7.6 m and 3 m for USL and CNL .
4. Do not kink the cord or allow it to contact oil, grease, chemicals,
hot surfaces, or sharp or abrasive objects.
5. This fan is to be operated ONLY with its OSHA compliant guards
in place to prevent persons and/or objects from contacting the
revolving propeller. Any other use voids warranty and may
create unsafe conditions.
6. Fan is intended for general air circulation ONLY. It must NOT be
used in potentially dangerous locations such as flammable,
explosive or chemical-laden atmospheres. Do not attach
ductwork to the fan.
Model
Size(inch)
Voltage(V)
Frequency(Hz)
Wattage(W)
AMPS(A)
RPM
Airflow(CFM)
Net Weight(KG)
Certification
Washdown Rated Stainless Steel
Pedestal and Wall Mounted Fan

GENERAL SAFETY INSTRUCTIONS

293018
24
115/230
60
310/305
2.85/1.55
1050/1060
7200
21.5
UL&cUL
7. Fan motor is equipped with an automatically resetting control
circuit that will disconnect power if the motor overheats. Always
unplug fan before removing guard, as motor may restart
unexpectedly.
8. Do not operate any fan with a damaged cord or plug. Discard
fan or return to an authorized service facility for examination
and/or repair.
9. Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area and
where it will not be tripped over.
10.Disconnect the fan when moving it from one location to another.
11.Make sure the fan is on a stable, flat surface while it is in
operation.
12.Disconnect the fan when removing the guards for cleaning.
The fan must be grounded and installed in A GFCI
Protected Branch Circuit. Improper connection may
create the risk of electrocution. Use of such adapters is
Do not depend on any switch as the sole means of
disconnecting power when installing or servicing the
fan. Failure to do so may result in fatal electrical shock.
I
MPORTANT: Surges in electrical power or excessive heat could
cause the fan to automatically shut off. Should this occur, wait
approximately 15 minutes for the fan to resume operation.
SPECIFICATION
293019
30
115/230
60
310/305
2.85/1.55
1050/1060
9600
23.7
UL&cUL
2
prohibited in Canada.
293020 293021
24
115/230 115/230
60
310/305 310/305
2.85/1.55 2.85/1.55
1050/1060 1050/1060
7200
25.9
UL&cUL UL&cUL
User's Manual
30
60
9600
28.3