Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Drilling in Masonry (Shift drill into
hammer mode if so equipped)
Use carbide tipped masonry bits. Refer to Drilling section.
Keep even force on the drill but not so much that you crack
the brittle material. A smooth, even flow of dust indicates
the proper drilling rate.
MAXiMUM RECOMMEnDED CAPACiTiEs
volts
amps
RPM
BPM
Capacity
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Versatrack™ (Fig. F)
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ peg hook
or Versatrack™ Trackwall. A damaged Versatrack™
peg hook or Versatrack™ Trackwall will not support
the weight of the tool.
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the peg hook. ONLY suspend tool on the
Versatrack™ Trackwall using the peg hook.
WARNING: Ensure that the tool weight does not
exceed the maximum rated weight for the selected
Versatrack™ hook.
120 AC Only
7.0
0–3100
0–52700
1–1/4" (32 mm) wood
1/2" (13 mm) steel
5/8" (16 mm) concrete
WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwall system.
1. Turn tool off, remove accessories, and disconnect it from
power source.
CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
the Versatrack™ Trackwall.
2. Mount the peg hook
13
3. Slide the peg hook through the loop
nOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Fig. F
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Repairs
WARNING:To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a CRAFTSMAN
factory service center or a CRAFTSMAN authorized
service center. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
•
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
English
to the Versatrack™ Trackwall.
on the tool.
8
13
8
7
Publicidad
Tabla de contenido
