Warnings – Assembly text instructions – Maintenance
English
WARNINGS
General
•
Do not use any sharp tools to open the pack-
aging.
•
We strongly advise against using power tools.
•
Tripping hazard, mind your step.
•
Do not put out cigarettes on the table.
•
Not grafitti proof.
•
Do not leave children unattended whilst playing
on the chair.
•
To avoid danger of suffocation, keep plastic bags
away from babies and children.
•
Colours can differ over years and from batch to
batch.
Product
•
Do not stand or jump on the table.
•
Do not drag the table, but carry it with minimum
2 people.
•
Anchoring the product has to be done by quali-
fied people.
•
For anchoring: use suitable bolts or screws from
a specialized store depending on the material
your terrace is made of.
•
Stackable up to 3 pieces and protect with blan-
kets.
•
Always stack the tables with 2 people.
•
Do not sit on the tabletop.
•
Max. 1 person or 120 kg per seat.
Powder-coating
•
White powder-coating requires more maintenan-
ce.
•
Do not use abrasive scouring powders or scou-
rers as they will scratch the surface.
•
Colour can fade to some extent when exposed to
UV.
•
Flame retarding - NEN-EN13501-1 A2-sl -
Satisfying the same criteria as Class B for the
SBI-test according to EN13823. In addition,
under conditions of a fully developed fire these
products will nog significantly contribute to the
fire load and fire growth.
•
Dark colors can get very hot in sunny weather.
Felt
•
Stains should be removed immediately with a
clean, soft cloth, particularly in case of dark-co-
30
loured liquids such as wine, ink, coffee coke, oild
and bird droppings. If left to dry, these liquids
may cause permanent damage!
•
Do not bleach to clean.
ASSEMBLY INSTRUCTIONS
3/4/5-seater - p12/16/20
1. Lay the tabletop upside down on the ground,
using the packaging to protect it.
2. Slide the legs into the frame as shown in the
diagram.
3. Attach the legs to the frame by inserting 2 M8x60
bolts with 2 M8 spring washers through the frame
and legs on each side, from the outside until they
emerge on the inside. Fasten them with an M8
spring washer and M8 nut on each bolt. Repeat
for the other legs.
Optional stacking spacer Position a stacking
spacer on each leg as shown in the drawing.
4. a. Now attach the seats to the legs using 4 M6
bolts and 4 M6 corrugated spring washers as
shown on the diagram.
b. Please note: tighten the bolts diagonally as
shown on the diagram, do not over-tighten! Max.
torque: 8 Nm of 4 kg /8,8 lb.
5. Turn the entire structure over.
Backrest - p24
1. Turn the table the right way up and attach the
backrest and the seats to the legs, using 4 M6
lock nuts, 4 M6 corrugated spring washers and
4 M6 washers in each case, as shown on the
diagram. Please note: tighten the bolts securely
but do not over-tighten! Max. torque: 8 Nm of 4
kg / 8,8 lb.
2. Position 2 allows more body depth.
Cushion - p25
1. Position the cushion on the seat so that the
silicone plug of the cushion fits into the hole of
the seat.
Floor fastening - p26
1. Turn the table upside down.
2. a. Drill a hole in the plastic cap.
b. Now pull the plastic cap out using a screwdri-
ver as shown on the drawing.
3. Assemble the ground anchoring set as shown in
the drawing. Do not completely tighten the bolt
yet.