Operation - Liberty Pumps Ascent II-ESW Manual De Instalación

3. To mount the toilet to a concrete floor, drill two holes
approximately 2-1/4" deep with a 5/16" masonry drill bit.
Insert plastic plugs into holes. If the floor is wood, bore a pilot
hole with a 1/4" drill bit. Fasteners not included.
4. Toilet to macerator connection:
a. Standard Installation:
Place the toilet in front of
the macerating tank and
apply silicone grease
(supplied) to the rubber
sealing lip of macerator.
Then slide the discharge
hub of the toilet into the
rubber sealing ring of the
macerator.
b. Behind Wall Installation:
To install the macerator behind a wall, an Extension Pipe Kit
(K001184, sold separately) is needed. Included in the kit
are an 18-3/4" long extension pipe, a decorative trim ring,
and a grease packet. Rubber rings seal both ends of the
extension pipe.
To prevent tearing, always grease both seals prior to
installing the pipe. Slip the decorative trim ring onto the
pipe. To install the pipe, no fasteners are required. Slip the
extension pipe over the toilet discharge, and then insert
the pipe into the macerator.
Liberty Pumps recommends only one extension pipe be
used.
5. Place the toilet over the holes in the floor. Slip the plastic china
protectors over the lag screws ensuring proper orientation.
Tighten lag screws (do not overtighten) and snap plastic caps
in place.
For proper flushing performance, ensure that the base of the
toilet is not below the base of the macerator. Check the
extension pipe, if applicable, with a level, and verify that the
pipe is either level or sloped toward the macerator unit and
away from the toilet.
6. Connect the water supply line to the fill valve, located directly
below the flush lever, on the bottom of the toilet tank.
Connection to the Discharge and Vent Flanges
To finish the installation, fasten the toilet to the floor and secure
the macerator discharge and vent piping.
NOTICE
 Do not use an air admittance valve or a mechanical
spring-loaded venting device, as these devices are one-way
valves. The air pressure in and outside the macerating pump
unit must be equal and a "cheater" vent will obstruct the
airflow in one direction and prevent proper toilet function.
Discharge Flange
The macerator has a PVC discharge flange with an integrated
check valve that can be configured in a horizontal or vertical
orientation. Standard 1" schedule 40 PVC pipe can be solvent
welded directly to the flange.
Excessive amounts of glue should be avoided. The check valve can
be removed from the flange if required.
5755000H
A full port ball or gate valve and a union should be installed in the
discharge pipe to facilitate the removal of the macerator or to
perform maintenance. Additionally, a drain off point is
recommended to allow the discharge piping to be drained.
Vent Flange
The macerator is equipped with a PVC vent flange, which can be
configured in a horizontal or vertical orientation. Standard 1-1/2"
schedule 40 PVC pipe can be solvent welded directly into the
flange.
The macerator must be vented to allow for proper toilet flush
performance. Depending on the installation, the product should
either be connected to the stack vent of the dwelling or vented
Apply grease to
(plumbed) directly outside. Vent in accordance with applicable
rubber ring
plumbing codes.
The macerator is not designed to support the discharge and vent
piping; proper pipe supports are required.
Connection to the Soil-stack or Sewer
The discharge piping can be made from 3/4" or 1" diameter PVC
pipe. Use long turn bends and avoid elbows where possible. The
connection to the soil-stack or sewer pipe must be made with an
approved connection, such as a T or Y fitting.

Operation

 Decorative covers must be installed for operation as a safety
NOTICE
 The macerating system is designed for human waste and
 During cleaning or when using a plunger, the macerator
 Do not hang bleach blocks or hypochlorite cleaners in the
 In the event of a power loss, the toilet can be used twice. Use
1. Ensure that the toilet and tank have been assembled per
2. Ensure any full port ball or gate valve in the discharge line is in
3. Open the shut-off valve and let the toilet tank completely fill.
4. Ensure the macerating unit has both decorative covers
Copyright © Liberty Pumps, Inc. 2018 All rights reserved.
RISK OF SERIOUS INJURY OR DEATH
WARNING
device is integrated into the covers to prevent unintended
operation. The unit may start when energized the first time.
toilet paper. Do not dispose of acids, alkalis, solvents, oils,
paint, paint strippers, food waste, and cotton swabs.
Off-the-shelf toilet cleansers will normally not hurt the
macerating unit.
could turn on.
toilet tank. These solutions have been shown to deteriorate
the plastic and neoprene components of the flush and fill
valves, and may cause leaks.
of sanitary fixtures such as a sink should be limited. Do not
use shower or tub as the macerating unit will fail to pump
until the power is restored.
instructions provided with the toilet tank.
the open (full flow) position.
Look for leaks at connections and verify that the toilet fill valve
float and the flush valve operate freely.
installed and is plugged in with the power supply turned on.
The green POWER LED should be illuminated steady.
a. If the green LED is blinking, confirm the decorative covers
are properly seated.
– 9 –