Lighting Instructions When Using Piezo; To Turn Off Heater - Dyna-Glo RMC-TT15 Manual De Mantenimiento, Operación E Instalación Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Propane is heavier than air. If propane leaks from a
connection or fitting, it sinks to the floor, collecting there
with the surrounding air, forming a potentially explosive
mixture. Obviously, propane leaks should be avoided,
so set up the propane supply with utmost care. Leak
check new connections or reconnections with a soap
and water solution and follow all connection instructions
herein. Also ask your propane dealer for advice on the
propane supply installation and ask him to check it if
there are any questions.
Direct-fired means that all of the combustion products
from burning propane enter the heated space. Even
though this heater operates very close to 100 percent
combustion efficiency, it still produces small amounts of
carbon monoxide. Carbon monoxide (called CO) is
toxic.
CO can build up in a heated space and failure to
provide adequate ventilation could result in death. The
symptoms of inadequate ventilation are:
headache
dizziness
burning eyes and nose
nausea
dry mouth or sore throat
So, be sure to follow advice about VENTILATION in
these operating instructions.
WARNING: Do not look over top of heater
(reflector) during ignition.
This heater may produce a small puff of
flame during ignition, which could result
in serious bodily injury.

Lighting Instructions when Using Piezo

WARNING: Review and understand the
Safety Information on page 3 before
lighting the Tank Top Heater.
CAUTION: Due to high surface tempera-
ture, keep children, clothing and furni-
ture away.
Keep burner and control compartment
clean.
This heater shall not be installed in a
bedroom or a bathroom.
WARNING: Hot while in operation: Do
not touch. Keep children, clothing,
furniture, gasoline and other liquids
having flammable vapors away.
1. Stop! Read all safety information.
2. Check that gas supply to the heater is on.
3. Turn heater regulator knob clockwise
position.
4. Wait five (5) minutes to clear out any air. Then smell
for gas, including near the floor. If you smell gas,
STOP! Follow "B" in the safety information on the
side of heater. If you do not smell gas, go to the next
step.
5. Turn heater regulator knob counterclockwise
to "Hi" position. Press in safety shut-off valve plunger
for five (5) seconds. (Fig. 3)
NOTE: The first time the heater is operated after
connecting the gas supply, the safety shut-off valve
plunger should be depressed for about thirty (30)
seconds. This will allow air to bleed from the gas
system.
6. With safety shut-off valve plunger pressed in, push
down and release piezo ignitor button. This will light
pilot. If needed, keep pressing piezo ignitor button
until pilot lights.
7. Keep safety shut-off valve plunger pressed in for
thirty (30) seconds after lighting pilot. After 30
seconds, release safety shut-off valve plunger.
8. If burner goes out, repeat steps 5 through 7 or use a
match. If heater will not light after repeated attempts,
do not attempt to repair heater. Return heater to
nearest authorized service center or to the address
on back of this manual, freight prepaid.
9. When burner is lit, turn heater regulator knob to
desired heat setting (LO, MED, HI).
10.Light both burners when maximum heat is needed.
Use one burner to conserve fuel.

To Turn Off Heater

1. Tightly close propane tank valve by turning clock-
wise.
2. Turn the heater regulator knob to the "OFF" position.
Wait at least 15 minutes for the heater to cool before
handling heater.
3. Always remove the heater from the propane tank
after each use. Do not store heater while attached to
propane tank in an enclosed area.
to "OFF"
5

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

Rmc-tt30Rmc-tt15pRmc-tt30p

Tabla de contenido