Operation; Break-In Procedure; Operating Procedure - Campbell Hausfeld HL5403 Instrucciones De Operación

Operating Instructions and Parts Manual
Installation (Continued)
wIRInG
1. Local electrical wiring codes differ
from area to area. Source wiring,
plug and protector must be rated for
at least the amperage and voltage
indicated on motor nameplate, and
meet all electrical codes for this
minimum.
2. Use a slow blow fuse or a circuit
breaker.
3. This product is for use on a nominal
120 volt circuit and has a grounding
plug that looks like the plug
illustrated in Figure 2. Make sure the
product is connected to an outlet
having the same configuration
as the plug. This product must
be grounded. In the event of an
electrical short circuit, grounding
reduces risk of electrical shock by
providing an escape wire for electric
current. This product is equipped
with a cord having a grounding
wire with an appropriate grounding
plug. Plug must be plugged into an
outlet that is properly installed and
grounded in accordance with all
local codes and ordinances.
Overheating, short
circuiting and fire
damage will result from inadequate
wiring.
Grounded
Outlet
Grounding Pin
Figure 2 - Grounding Method
Minimum Gauge of Extension Cord
25 ft.
14
Use of an extension cord may cause excess
heat to motor. This could lead to tripped
breaker (at electrical panel) or tripped
thermal overload (on compressor motor).
If this occurs, eliminate extension cord and
plug compressor directly into electrical
outlet. Avoid using extension cords; use
longer air hose(s) instead.
LUbRICatIOn
Follow lubrication instructions before
operating compressor.
Use oil shipped with the compressor. Do
not use regular automotive oil such
as 10w-30. Additives in regular motor
oil can cause valve deposits and reduce
pump life. For maximum pump life,
drain and replace oil after the first hour
of run time.
The compressor pump takes
approximately 175mL (6 oz) of oil. The
sight glass, located on the crankcase
portion of the pump, is used to
determine proper oil level. Fill the
crankcase with oil until the level is in
the middle of the sight glass. Avoid
overfilling by adding oil gradually and
checking the oil level with the sight
glass several times. Add enough oil to
reach the "max" level on the sight glass.
Proper oil level is illustrated in Figure 3.
TEST RESET
Figure 3 - Proper Oil Level
50 ft. 100 ft.
12 10
This unit is shipped
without oil!
Max.
Min.
4

Operation

beFORe FIRst staRt-UP

bReak-In PROCeDURe

(Complete this procedure before using
compressor for the first time. Once
completed, it is not necessary to repeat.)
1. Open drain valve located on bottom
of tank.
2. Turn on/off switch to OFF position.
3. Plug in power cord.
4. Turn on/off switch to ON position
and run compressor for 30 minutes.
5. Turn on/off switch to OFF position.
6. Unplug power cord.
7. Close drain valve
The compressor is now ready for use.

OPeRatInG PROCeDURe

1. Turn switch to OFF position and plug
in power cord.
2. Turn regulator knob
counterclockwise to close air flow.
3. Turn switch to AUTO position.
4. Compressor will build to maximum
pressure and shut off.
5. With hose attached to outlet of
compressor, attach tire chuck or
other tool to open end of hose.
6. Adjust regulator to proper pressure
for tool or tire. Operate tool per
instructions.
As air is depleted from the tank by
use of a tire chuck, tool, etc., the
compressor will restart automatically
at its preset "cut-in" pressure. When
a tool is being used continuously,
the compressor will cycle on and off
automatically.
7. Turn switch to OFF position, unplug
power cord and drain tank of air
when finished using compressor.