Coelbo SPEEDBOX DUO Instrucciones Para La Instalación Y Utilización página 12

EXPERT MENU. Special configuration, there is no need to adjust these values, they are factory set.
Using pq we can change the values and press ENTER for validation. Whenever we want to quit the configuration sequence press MENU. After every
ENTER it will appears automatically the different screens that constitute the configuration sequence.
M E N U
E X P E R T
M A X . F R E Q U E N C Y
5 0 . 0 H z
P R O P O R T I O N A
9 2
I N T E G R A L
1 0 0
A C C E L E R A T I O N
4 0
D E C E L E R A T I O N
5 0
M O T O R T Y P E
T H R E E P H A S E
S W I T C H I N G
8 K H z
REGISTER OF OPERATION DATA AND ALARMS.
By using simultaneously MENU + p during 3" is acceded to REGISTER OF OPERATION DATA AND ALARMS, by mean of ENTER we can
advance through the sequence, once finished the sequence it returns to the main display. This is all the sequence:
A L A R M
A 1 D R Y
0
A 2 O V E R L O A D
0
A 3 O V E R L O A D
0
A 4 L E V E L
0
A 5 P R E S S U R
0
A 6 O V E R T E M P
0
A 7 O V E R T E M P
0
A 8 H I G H
0
A 9 L O W
0
DRY RUN. Number of dry-running alarms.
n
OVERLOAD P1. Number of overload alarms in pump 1.
n
OVERLOAD P2. Number of overload alarms in pump 2.
n
LEVEL. Number of level alarms.
n
PRESSURE SENSOR. Number of damaged pressure sensor alarms.
n
OVERTEMP P1. Number of alarms by excessive temperature in pump 1.
n
OVERTEMP P2. Number of alarms by excessive temperature in pump 2.
n
HIGH VOLTAGE. Number of alarms by excessive temperature.
n
LOW VOLTAGE. Number of alarms by excessive temperature.
n
L
U V W
F R E Q .
MENU+p
R E G I S T E R
ENTER
R U N
ENTER
P 1
ENTER
P 2
ENTER
ENTER
E S E N S
ENTER
P 1
ENTER
P 2
ENTER
V O L T A G E
ENTER
V O L T A G E
To start the configuration secuence press MENU + ENTER during 3"
By mean of keys pq it can be adjusted the maximum working frequency.
PI parameter, factory set. For any doubt contact with the manufacturer.
Using pq it can be adjusted the desaceleration. Rank 5-20 (Hz/s). Press ENTER to
confirm.
Using pq it can be adjusted the desaceleration. Rank 5-20 (Hz/s). Press ENTER to
confirm.
By mean of keys pq it can be adjusted the motor type: Single phase/Three phase.
In case of single phase disconnect black cable. (fig.4)
Using pq it can be adjusted the commutation frequency 8KHz o 4KHz. Press ENTER to
confirm. For installations with submersible pumps or where the cable of the device to the
pump exceeds 20m, it is advisable to work in a commutation frequency of 4Khz.
A 1 3
0
A 1 4
0
A 1 5
0
F U N C T
0
S T A R T S
0
S T A R T S
0
O N
0
O N
0
T I M E
0
M A I N S
1
MIN PRESS. Number of minimum pressure alarm.
n
SHORTCIRC P1. Number of short circuit alarms in pump 1.
n
SHORTCIRC P2. Number of short circuit alarms in pump 2.
n
STARTS COUNT P1. Sows the number of starts of pump 1.
n
STARTS COUNT P2. Shows the number of starts of pump 2.
n
ON TIME P1. Shows the operating time of the pump 1 in hours.
n
ON TIME P2. Shows the operating time of the pump 2 in hours.
n
TIME INVERTER. Shows the operating time of the inverter in hours.
n
MAINS COUNTER.Shows the number of connections to the electric supply.
n
-11-
M I N . P R E S
ENTER
S H O R T C I R
ENTER
S H O R T C I R
ENTER
I O N R E G
ENTER
C O U N T
ENTER
C O U N T
ENTER
T I M E P 1
ENTER
T I M E P 2
ENTER
I N V E R T E
ENTER
C O U N T E
S
C P 1
C P 2
P 1
P 2
R
R