imtech Remote Control for iMatJet Instrucciones De Uso página 5

❾
Remote control of the iMatJet®
❾
Remote control of the iMatJet®
The two control levers are used to separately operate the
The two control levers are used to separately operate the
two drives of the iMatJet®. Acceleration, turning speed and
two drives of the iMatJet®. Acceleration, turning speed and
radius may vary at different speeds, angles of rotation and
radius may vary at different speeds, angles of rotation and
water conditions.
water conditions.
Hibernation and Autohold
Hibernation and Autohold
If you want to temporarily just chill and not ride, you can
If you want to temporarily just chill and not ride, you can
attach the remote control to the top of the air mattress under
attach the remote control to the top of the air mattress under
the right armrest using Velcro.
the right armrest using Velcro.
Autohold switch on: If you want to drive straight for a while,
Autohold switch on: If you want to drive straight for a while,
❾
you can activate the "GAS AUTOHOLDED" function as
you can activate the "GAS AUTOHOLDED" function as
follows: Press both control levers
follows: Press both control levers
simultaneously until "GAS AUTOHOLDED" appears in the
simultaneously until "GAS AUTOHOLDED" appears in the
display. [Figure 4]
display. [Figure 4]
During the "GAS AUTOHOLDED" mode, you can compensate
During the "GAS AUTOHOLDED" mode, you can compensate
Switching off the function: Press the button ❶.
Switching off the function: Press the button ❶.
for any currents with the control levers at any time.
for any currents with the control levers at any time.
Illustrations - what you can see on the display
Illustrations - what you can see on the display
Figure 1: Plug symbol (charging)
Figure 1: Plug symbol (charging)
Figure 2: 6 filled bars (fully charged)
Figure 2: 6 filled bars (fully charged)
Figure 3: "CONNECTED" (connected to the iMatJet®)
Figure 3: "CONNECTED" (connected to the iMatJet®)
Figure 4: "GAS AUTOHOLDED"
Figure 4: "GAS AUTOHOLDED"
(autohold function switched on)
(autohold function switched on)
Figure 5: Request for charging
Figure 5: Request for charging
Figure 6: Battery status of the iMatJet®
Figure 6: Battery status of the iMatJet®
Figure 7: Battery status of the remote control
Figure 7: Battery status of the remote control
Figure 8: Serial number of the remote control.
Figure 8: Serial number of the remote control.
Displayed when switched off.
Displayed when switched off.
Figure 9: Number of operating hours.
Figure 9: Number of operating hours.
Push both control levers down
Push both control levers down
and press the button.
and press the button.
Reverse function
Reverse function
If you want to use the control levers
If you want to use the control levers
around or have accidentally moved the right motor to the
around or have accidentally moved the right motor to the
left side of the base plate and the left motor to the right
left side of the base plate and the left motor to the right
side, you can reverse the operation using the control lever:
side, you can reverse the operation using the control lever:
Press the button
Press the button
Other functions
Other functions
You have the option of reading the current battery status
You have the option of reading the current battery status
❾
[Figure 6] of your iMatJet® on the remote control. When
[Figure 6]
forward and the button
forward and the button
6 filled bars are visible, the batteries are full. The less
6 filled bars are visible, the batteries are full. The less
bars are filled, the more energy is already consumed.
bars are filled, the more energy is already consumed.
A beep (5 sec beep, 10 sec pause...) will inform you
A beep (5 sec beep, 10 sec pause...) will inform you
when it is time to return to shore. In addition, the prompt
when it is time to return to shore. In addition, the prompt
for charging
for charging
battery symbol flashes. This is the case when the battery
battery symbol flashes. This is the case when the battery
has about 7 minutes of remaining capacity. The beep is
has about 7 minutes of remaining capacity. The beep is
off by pressing button ❶.
off by pressing button ❶.
no longer audible when the remote control is switched
no longer audible when the remote control is switched
[ 1 ]
[ 5 ]
[ 8 ]
❾
❾
the other way
the other way
❶
❶
5 times. [10]
5 times. [10]
of your iMatJet® on the remote control. When
[Figure 5] appears in the display and the
[Figure 5] appears in the display and the
[ 10 ] [ 7 ]
[ 4 ]
[ 9 ]
[ 6 ]
EU Declaration of Conformity
EU Declaration of Conformity
in the sense of EU Directive 2014/53/EU
in the sense of EU Directive 2014/53/EU
The manufacturer:
The manufacturer:
imtech GmbH &Co.KG
imtech GmbH &Co.KG
Auf Stocken 18
Auf Stocken 18
D-78073 Bad Dürrheim
D-78073 Bad Dürrheim
hereby declares that, by virtue of its design and construction,
hereby declares that, by virtue of its design and construction,
and in the form in which it is placed on the market, the product
and in the form in which it is placed on the market, the product
complies with all the relevant essential health and safety
complies with all the relevant essential health and safety
requirements of the Radio equipment Directive, including any
requirements of the Radio equipment Directive, including any
amendments thereto in force at the date of this declaration.
amendments thereto in force at the date of this declaration.
Make: imtech
Make: imtech
Product description: Remote Control for iMatjet+charger
Product description: Remote Control for iMatjet+charger
Item number: 2019-787-04
Item number: 2019-787-04
Furthermore, compliance with the following EU directives
Furthermore, compliance with the following EU directives
including their amendments valid at the time of this declaration
including their amendments valid at the time of this declaration
is declared:
is declared:
EMC Directive 2014/30 / EU ● RoHS Directive 2011/65 / EU and
EMC Directive 2014/30 / EU ● RoHS Directive 2011/65 / EU and
2015/863 EU ● REACH Regulation 2020/171 / EU
2015/863 EU ● REACH Regulation 2020/171 / EU
[ 2 ]
The following harmonized standards have been applied:
The following harmonized standards have been applied:
EN 300440: 2017-03 V2.1.1 ● EN 300328: 2016-11 V2.1.1
EN 300440: 2017-03 V2.1.1 ● EN 300328: 2016-11 V2.1.1
EN 301 489-1: 2017-03 V2.2.0 ● EN 301 489-3: 2017-03 V2.1.1
EN 301 489-1: 2017-03 V2.2.0 ● EN 301 489-3: 2017-03 V2.1.1
EN 301 489-17: 2017-03 V3.2 ● EN 62479: 2010
EN 301 489-17: 2017-03 V3.2 ● EN 62479: 2010
EN 60950-1: 2006+A11: 2009+A1: 2010+A12: 2011
EN 60950-1: 2006+A11: 2009+A1: 2010+A12: 2011
Registration numbers WEEE DE85344424
Registration numbers WEEE DE85344424
[ 3 ]
BATT. DE24171218 / VERP. DE2618437491737
BATT. DE24171218 / VERP. DE2618437491737
Bad Dürrheim, on the 23 June 2021
Disposal and recycling
Disposal and recycling
As a consumer, you are legally obligated
As a consumer, you are legally obligated
to dispose of waste electrical equipment
to dispose of waste electrical equipment
properly. The same applies to batteries.
properly. The same applies to batteries.
Do not use water
Do not use water
for lithium fires if
for lithium fires if
necessary extinguish
necessary extinguish
as metal or lithium fire
as metal or lithium fire
A2: 2013
A2: 201
+
+
Bad Dürrheim, on the 23 June 2021
5