Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
A - CONNECTIONS
230VAC 50/60 Hz POWER SUPPLY (120VAC/60 Hz UPON
J1
L-N
REQUEST)
COURTESY LIGHT OR BLINKER (MAX 40 W )
J2
U
MOTOR COMMON CONNECTION
V-W
MOTOR PHASES AND CAPACITOR CONNECTIONS
AERIAL
RADIO ANTENNA
A+A-
POWER SUPPLY FOR ACCESSORIES 24 Vdc
COM.
CONTACTS COMMON UNIT
J3
K BUTT.
CONTACT OF A SINGLE IMPULSE (NO)
PHOTO
PHOTOCELLS CONTACT (NC)
EDGE
SAFETY STRIP CONTACT IN OPENING AND CLOSING (NC)
A+ TEST
ACCESSORIES POWER SUPPLY +24 Vdc
FUSES
F1 =>
T100mA
F2 =>
T6,3A
RELAYS AND MOTOR CONTROL
K1 =>
Flasher control
K2 =>
Opening travel control
K3 =>
Closing travel control
Q4 =>
TRIAC Motor control, open and close
B - SETTINGS
OPERATION MICROSWITCHES
DIP 1
(ON) CHECKING THE ROTATION DIRECTION OF THE MOTOR (POINT C)
DIP 1
(ON) ENABLING OF MANNED POSITION SETTING (POINT D)
DIP 2
(ON) TIMING (POINT E)
DIP 1-2 DIP 1 to ON FOLLOWED BY DIP to 2 ON - READ IN/CANCELLATION RADIO CODES FOR MOTOR
CONTROL ONLY FOR CRX MODELS (POINT F)
OPERATING MICROSWITCH
DIP 3
ON - Automatic Closing ENABLED
DIP 4
ON - Photocells active only in closing
DIP 5
ON - For external flasher
DIP 6
ON - STEP BY STEP
DIP 7
ON - Safety strip self test ENABLED
DIP 8
ON - Blinker pre-flashing
TORQUE - ELECTRONIC TORQUE REGULATOR
The torque is regulated by rotating the Trimmer TORQUE, varying the output voltage of motor
ends,(when rotated clockwise, more torque Is transmitted to the motor).
Such torque is automatically included 3 seconds after the start of every
operating cycle.
This allows the motor to have the maximum pickup when it starts.
NOTE: IN CASE THE ABOVE TRIMMER IS SET FOLLOWING THE PROGRAMMING PROCEDURE, THE
SLOWING STROKE STARTING POINT CAN CHANGE (ANTICIPATING OR DELAYING THE SET
VALUE), THEREFORE UPON A NEW TRIMMER SETTING, A NEW TIME ADJUSTMENT IS
RECOMMENDED.
LED SIGNALS
DL1 - (Red)
- Programming operated
DL2 - (Green)
- Radio programming activated (models CRX only)
DL3 - (Red)
- Safety strip contact (NC)
DL4 - (Red)
- Photocell contact (NC)
DL5 - (Red)
- K BUTT command light
DL6 - (Red)
- Shutter is closing
DL7 - (Green)
- Shutter is opening
C - CHECKING THE ROTATION DIRECTION OF THE MOTOR
This control is carried out to facilitate the installation of the system or any possible future
control.
WITH FENCE LOWERED AND LOWER STROKE END SWITCH CORRECTLY SET.
1 - Put DIP 1 to ON => The LED DL1 starts blinking;
CAUTION: in case the pushbutton PROG is not operated within 1 min, the LED turns off, the
system maintains the present configuration, see para. "D-MANNED POSITION SETTING".
OFF - Photocells always active
OFF - For internal courtesy light
OFF - AUTOMATIC
OFF - Safety strip self test DISABLED
OFF - Blinker normal flashing
SW J AND RADIO
DO NOT TOUCH THE JUMPER ! IF IT IS REMOVED THE OPERATOR
CRX
J4
DOESN'T MOVE !
NOT CRX
CONNECTOR FOR EXTERNAL RADIO RECEIVER 24 Vdc (NOT CRX
J5
RADIO
MODELS)
J6
RADIO
IN BUILT RADIO MODULE (MODELS CRX)
TR1
TORQUE
ELECTRONIC TORQUE REGULATOR
S1
PROG.
PUSH-BUTTON FOR THE PROGRAMMING
,
2 - Depress and maintain the pushbutton PROG (motion is performed in manned position
setting, open-stop-close-stop-open-etc.) the fence will open (DL7 green lit).
a - In case the fence closes instead of opening (DL6 RED LIT) release immediately the
pushbutton PROG and set the close stroke end switch.
b - In case the fence closes instead of opening (DL7 GREEN LIT) exchange the connection
of motor wires V and W on the electrical unit, or connection blocks 5 and 6 on the
stroke end unit JOLLY.
3 - Set the opening stroke end switch. Ensure the end stroke system stops the motor on
completion of opening stroke.
4 - After 3 sec of opening or close travel, the electronic torque increase gets in operation. Set
the electronic torque through the trimmer TORQUE.
5 - On completion of checks and setting of trimmer, set the DIP 1 to OFF. The LED DL1 turns off
(in case still lit) to indicate the end of control phase.
N.B.: While performing this check, photocells and safety strips are overridden.
D - MANNED POSITION OPERATION
In such mode the remote control will not operate.
Set DIP 1 to ON the LED DL1 starts flashing. Flashing will end within 1 minute, unless any
operation is initiated.
To operate the fence depress and maintain the pushbutton "K Button".
In case the pushbutton is released the fence stops. Further depressing the pushbutton will
command motion of the fence in the opposite direction.
N.B.: While performing this operation, photocells and safety strips are overridden.
E - TIME SETTING
Setting must be performed with the fence fully closed, with STROKE END SWITCHES SET.
1 - Put DIP 2 to ON => the LED DL1 emits short blinkings.
2 - Depress the pushbutton PROG => the fence opens
3 - After 2 s from the fence reaches the full open position, depress the pushbutton PROG to
set the operation time of the fence.
4 - Wait as long as you want the shutter to remain open before the automatin closing
(excluded by DIP 3 OFF).
5 - Push the button PROG. to command the shutter closing, also the pause time count before
the automatic closing stops - max. 5 minutes (the LED DL1 stops flashing). On triggering of
close stoke end switch, the fence stops.
6 - AT THE END OF THE PROGRAMMING PUT THE DIP 2 BACK TO OFF.
N.B. During the programming the safeties (photocells and safety strips) are active and
their intervention stops the programming (the led dl1 which was lightening now has a
costant light). To repeat the programming set the dip 2 on off), close the door following
the procedure "C - CHECKING THE ROTATION DIRECTION OF THE MOTOR" and repeat the
programming described above.
F - RADIO CODE LEARNING PROCEDURE (CRX MODELS ONLY)
The position of the door does not affetc the code memorisation.
1 - Set DIP 1 to ON and subsequently DIP 2 to ON => DL1 programming led will lighten for 10 s,
witch is the time required for they code's programming.
2 - Following code setting through DIPs inside the remote control, repress the remote control
button (normally the A channel) within the 10 s set. If the remote control is correctly
matched, the DL2 green led flashes shortly.
3 - The codes' programming time is automatically renewed to read in the following remote
control.
4 - To end the programming wait 10 s, or press for a while the PROG. button => DL1
programming led will stop lightening.
17
G
B
Publicidad
Tabla de contenido
