Technical Data And Drawings; Electrical Data; Transformation; Positioning - Lotus CF4-68ETX Instrucciones Para La Instalación Y El Uso

The data plate is attached to the back panel (see drawing electrical connection point) and contains all the information
necessary for connection.
DIMENSIONS
MODELS
cm
80 x 60 x 91h
CF4-68ET
CF6–610ET 100 x 60 x 91h
CFM4-66ET 60 x 60 x 91h
CFM4–68ET 80 x 60 x 91h
CFM6-610ET 100 x 60 x 91h
60 x 60 x 91h
CFMC4-66ET
DIMENSIONS
MODELS
cm
CF4-68ET 80 x 60 x 91h
CF6–610ET 100 x 60 x 91h
60 x 60 x 91h
CFM4-66ET
CFM4–68ET 80 x 60 x 91h
100 x 60 x 91h
CFM6-610ET
CFMC4-66ET 60 x 60 x 91h
CF4-68ET 80 x 60 x 91h
CFM4-66ET 60 x 60 x 91h
CFM4–68ET 80 x 60 x 91h
60 x 60 x 91h
CFMC4-66ET
On positioning the appliance, ensure that it is perfectly levelled. Small adjustments can be made by screwing the
adjustable feet up or down. The master switch or the socket point must be in proximity to the appliance and easily
accessible. It is advisable to place the oven under an extractor hood to ensure rapid elimination of steam. If the
appliance is placed near a wall or partition, kitchen furniture or decorative coverings, etc., these must be fire-proof or
coated with fire-proofing. Local fire prevention regulations must be observed. There must be maximum clearance
between the front edge of the cabinet and the appliance.

REGULATIONS, TECHNICAL STANDARDS AND SPECIFICATIONS

Installation must be carried out in accordance with:
•
current accident prevention legislation;
•
current VDE specifications.
The installation, start-up and maintenance of this appliance must be carried out only by qualified fitters. All installation
operations must be in accordance with current regulations. The manufacturer declines all responsibility for
malfunctioning due to bad or faulty installation.
Attention: international regulations require that a omni pole cut-out device with contact opening of at least 3 mm be
fitted on the wiring leading to the appliance.
The terminal board is situated behind the front panel. The electrical wiring must be no less than HO5 RN F and have a
section suitable for the appliance (see 1.1). Secure the wiring with the wiring clips. Connect the wire ends to their
terminals on the terminal board. The earthing wire must be longer than the other wires so that it will disconnect after the
live wires in the event of the fastener breaking.
GB

TECHNICAL DATA AND DRAWINGS

ELECTRICAL DATA

POWER
SUPPLY POWER KW
400Vac3N 50/60 Hz
400Vac3N 50/60 Hz
400Vac3N 50/60 Hz
400Vac3N 50/60 Hz
400Vac3N 50/60 Hz
400Vac3N 50/60 Hz

TRANSFORMATION

POWER
SUPPLY POWER KW
230Vac3 50/60 Hz
230Vac3 50/60 Hz
230Vac3 50/60 Hz
230Vac3 50/60 Hz
230Vac3 50/60 Hz
230Vac3 50/60 Hz
230Vac 50/60 Hz
230Vac 50/60 Hz
230Vac 50/60 Hz
230Vac 50/60 Hz

POSITIONING

INSTALLATION

ELECTRICAL CONNECTION

32
IE
MAXIMUM MAXIMUM
ABSORPTION A
8,62 13,04
11,62 14,69
9,05 13,26
9,05 13,26
12,05 14,91
9,65 11,85
MAXIMUM MAXIMUM
ABSORPTION A
8,62 22,59
11,62 27,42
9,05 22,78
9,05 22,78
12,05 27,61
9,65 22,35
8,62 37,48
9,05 39,35
9,05 39,35
9,65 39,46
POWER SUPPLY
CABLE
5 x 1,5 mm²
5 x 1,5 mm²
5 x 1,5 mm²
5 x 1,5 mm²
5 x 1,5 mm²
5 x 1,5 mm²
POWER SUPPLY
CABLE
4 x 2,5 mm²
4 x 4 mm²
4 x 2,5 mm²
4 x 2,5 mm²
4 x 4 mm²
4 x 2,5 mm²
3 x 6 mm²
3 x 6 mm²
3 x 6 mm²
3 x 6 mm²