Connecting The Water Lines; Connecting The Drain Line - LG WM0742H A Serie Guia Del Usuario

Ocultar thumbs Ver también para WM0742H A Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

I N S TA L L AT I O N I N S T R U C T I O N S

CONNECTING THE WATER LINES

• IMPORTANT: Use new hoses when installing
the washer. Do NOT reuse old hoses.
• IMPORTANT: Use ONLY the inlet hoses
provided by LG with this laundry product.
Aftermarket hoses are not guaranteed to fit or
function correctly. Other hoses may not tighten
correctly and could cause leaks. Subsequent
damage to product or property will not be
covered under the terms of LG's warranty.
• Water supply pressure must be between
14.5 PSI and 116 PSI (100~800 kPa). If the
water supply pressure is more than 116 PSI, a
pressure reducing valve must be installed.
• Periodically check the hose for cracks, leaks,
and wear, and replace the hose if necessary.
• Make sure that the water lines are not stretched,
pinched, crushed, or kinked.
• The washer should never be installed or stored
in a location subject to freezing temperatures.
Damage to the water lines and internal
mechanisms of the washer can result. If the
washer was exposed to freezing temperatures
prior to installation, allow it to stand at room
temperature for several hours before use.
Water
Inlets
NOTE: Do not cross-thread the hose fittings.
2
Attach the hot water line to the red hot water
inlet on the back of the washer. Attach the
cold water line to the blue cold water inlet on
the back of the washer. Tighten the fittings
securely.
1
Water Hose
Rubber Seal
(to water inlet
on washer)
Water Hose
(to tap)
Rubber Seal
1
Insert a rubber seal into the threaded
fittings on each hose.
Water Tap
Attach the hot water line to the hot water
3
tap. Attach the cold water line to the cold
water tap.
Tighten the fittings securely. Open the water
taps fully to check for leaks.
I N S TA L L AT I O N I N S T R U C T I O N S

CONNECTING THE DRAIN LINE

• The drain hose should always be properly
secured. Failure to properly secure the drain
hose can result in flooding and property
damage.
• Do not install the end of the drain hose higher
than 96 in. (244.8 cm) above the bottom of the
washer.
• The drain must be installed in accordance with
any applicable local codes and regulations.
• Make sure that the water lines are not stretched,
pinched, crushed, or kinked.
Option 2: Laundry Tub
Elbow
Bracket
Laundry
Tub
Tie
Strap
Drain
Hose
Clip the end of the hose into the elbow bracket.
Hang the end of the drain hose over the side of
the laundry tub. Use tie strap to secure the drain
hose in place.
NOTE: Total height of the hose end should not
exceed 96 in. (244.8 cm) from the bottom of the
washer.
Option 1: Standpipe
Elbow
Bracket
Tie Strap
Stand
Pipe
Drain
Hose
Clip the end of the hose into the elbow bracket.
Insert the end of the drain hose into a standpipe.
Use tie strap to secure the drain hose in place.
NOTE: Total height of the hose end should not
exceed 96 in. (244.8 cm) from the bottom of the
washer.
Option 3: Floor Drain
Drain Hose
Floor Drain
Insert the end of the drain hose into the floor
drain. Secure the hose in place to prevent it
from moving.
1

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido