Assembly; Making The Electrical Connection; Important - HAMPTON BAY WINDWARD IV Guía De Uso Y Mantenimiento

Assembly – Hanging the Fan (continued)
6

Making the electrical connection

IMPORTANT: Use the wire connecting nuts supplied with
your fan. Secure the connectors with electrical tape and
ensure there are no loose strands or connections.
Connect the ground conductor of the 120-Volt supply (this
may be a bare wire or a wire with green colored insulation)
to the green ground lead(s) (II) of the fan.
Connect the fan motor white wire (LL) to the receiver (NN)
white wire (LL) using a wire nut.
Connect the fan motor black wire (KK) to the receiver (NN)
black wire (KK) using a wire nut.
Connect the fan motor blue wire (JJ) to the receiver (NN)
blue wire (JJ) using a wire nut.
Connect the receiver (NN) red wire (OO) to the supply black
(hot) wire (KK) using a wire nut.
Connect the receiver (NN) white wire (LL) to the supply white
wire (neutral) (LL) wire using a wire nut.
After connecting the wires, spread them apart so that the
green (II) and white wires (LL) are one side of the outlet box
(MM) and the black wire (KK) is on the other side.
Turn the wire connecting nuts upward and carefully push
the wiring into the outlet box (MM).
NOTE : The frequencies on your receiver and remote control
have beet preset at the factory. Before installing the receiver,
make sure the dip switches on the receiver and remote control
are set to the same frequency. The dip switches on the remote
control are located inside the battery compartment.
WARNING:
Each wire nut supplied with this fan is designed
to accept up to one 12-guage house wire and two wires from
the fan. If you have larger than 12-guage house wiring or
more than one house wire to connect to the fan wiring,
consult an electrician for the proper size wire nuts to use.
MM
NN
JJ LL
KK LL
7
Mounting the fan
WARNING: When using the standard ball/downrod
mounting, the tab in the ring at the bottom of the mounting
plate must rest in the groove of the hanger ball. Failure to
properly seat the tab in the groove could cause damage to
the wiring.
Align the locking slots of the ceiling canopy (C) with the
two screws in the mounting bracket (A). Push up to engage
the slots, and turn clockwise to lock the canopy in place.
Firmly tighten the two mounting screws.
Install the remaining two mounting screws into the holes in
the canopy (C) and tighten rmly.
Install the decorative canopy ring by aligning the ring's
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock in place.
Close-To-Ceiling Mounting
Carefully unhook the fan from the mounting bracket (A) and
align the locking slots of the ceiling canopy (C) with the two
screws in the mounting bracket (A). Push up to engage the
slots and turn clockwise to lock the canopy in place.
Immediately tighten the two mounting screws rmly.
WARNING:
provided only as an aid to mounting. Do not leave the fan
assembly unattended until all four canopy screws are
engaged and rmly tightened.
Install the remaining two mounting screws into the holes in
the canopy (C) and tighten rmly.
Install the decorative canopy ring by aligning the ring's
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock it in place.
l P a e e s o c t n c a
9
A
D
The locking slots of the ceiling canopy are
A
D
H A M P O T
1 t 8 - 7 7 5 - 7 2 0 - 1 3 f 3 r o u f t r e h a r
N B Y A C . O M
s s s i a t c n . e