Suncourt TW208P Instrucciones De Instalación

INSTALLATION INSTRUCTIONS FOR THE THRUWALL ROOM TO ROOM FAN
MODEL: TW208P
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT NOTICE
WARNING
- To Reduce The Risk Of Fire Or Electric Shock, Read These Instructions Before Installing Your Thruwall TW208P Room To
Room Fan.
This fan is not to be installed in an outside wall.
Do not use in wet or damp locations.
Do not install in fire rated walls.
Do not use in a window.
Do not connect to a secondary remote speed control.
Not for bathroom use.
Instructions are available at www.suncourt.com
With the use of any electrical appliance, it is important to observe all basic precautions to minimize the risk associated with use, such as
electrical shock, fire, or injury to persons. If you have doubts or are unfamiliar with this type of installation work, seek the services of a qualified
electrician. Suncourt assumes no responsibility for installation of the ThruWall Fan
adhere to applicable building and/or electrical codes.
NEVER EXPOSE YOUR THRUWALL TO TEMPERATURES OVER 140°F (60°C)
Warning
- To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Observe The Following:
a) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
b) Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on
accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device such as a tag to the service panel.
c) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
d) When cutting or drilling into wall, do not damage electrical wiring and other hidden utilities.
e) NEVER place a switch where it can be reached from a tub or shower.
f) Prior to installation of the TW208P fan, switch power off at service panel and lock service panel to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
STEP BY STEP INSTRUCTIONS
Step 1.
Depending on your needs, the ThruWall
Conversely, cold air falls and is found near the floor. The temperature of the air near the ceiling may be as much as 10°F to 15°F higher than near the floor. Start
by making sure that there are NO studs, water, drain, electrical or other obstructions in the wall where you wish to install the unit. Please see the airflow direction
label on the housing.
Step 2.
Place template flush against wall. Check for level and tape in place. Note: The wall that the template is taped to will be the fan output side.
Step 3.
Cut out the opening with a small drywall saw. Take care not to damage the edge of the drywall since you will be installing drywall anchors close to the
hole to mount the grille.
Step 4.
Insert the grille with fan attached into the hole that you just cut. Make sure the fan is level and that the grille completely covers the opening. Mark the
location of the 4 mounting holes.
Step 5.
Remove fan from hole and drill mounting holes with a sharp 3/16" drill bit. Insert wall anchors in mounting holes.
Step 6.
Project the edge of the round section of the cutout onto the inside of the other wall board in three places, approximately 120° apart. Use a small square or
a piece of cardboard that has an exact 90° angle to mark the cutout points on the inside of the other wall.
Step 7.
Use a small pin or very small drill bit (1/32" or smaller) to punch or drill these three marks to the outside of the other wall.
Step 8.
Place the sleeve without the grille attached, against the outside of the wall and center its location using the three holes that you made. Then trace the
outside of the sleeve with a pencil. Cut the circular opening with a small drywall saw. Cut inside the pencil line. Take care not to damage the edge of the drywall.
You will be installing drywall anchors close to the holes to mount the grille.
Step 9.
Take the electrical box cover off of the molded on electrical box and install a 3/8" strain relief that is appropriate for your 120VAC power supply wire
and/or conduit.
Step 10.
Insert your 120VAC power supply wires through the strain relief and use the providedwire nuts to connect the white (common), black (hot), and green
(ground) wires from the TW208P ThruWall fan to the appropriate common, hot and ground wires of your incoming power wires.
Step 11.
Check to see that your strain relief is securely fastened and re-attach the electrical box cover.
Step12.
Insert the metal sleeve with grille into the cutout opening (fan output side) and screw the grille down snugly.
Step13.
Insert the other metal sleeve into the cutout opening (fan suction side) and snug the flange up against the wall material.
Step14.
Position the unattached plastic grille over the metal sleeve that was just inserted so that the logo on the center of the grille is right side up and that one of
the mounting holes is in the top center. Adjust the metal sleeve so that the three U shaped cut outs in the flange match up with the mounting holes in the grille. Mark
the location of all 3 wall anchors.
Step 15.
Drill the holes on the wall for the anchors with a sharp 3/16" drill bit. Install wall anchors and screw the grille down snugly.
OVERTIGHTEN!
TM
can be installed high or low on the wall. Please note that warm air rises, thus is found near the ceiling.
. For your safety and protection follow all instructions and
TM
DO NOT OVERTIGHTEN!
™
DO NOT