Environmental Protection; Declaration Of Conformity - KRESS KUB30 Manual De Instrucciones

Using The Sight Light
Before operation, the LED light will be
activated when the On/Off switch is
slightly depressed, and will automatically
turn off 20 seconds after the On/Off
switch is released.
The Battery of impact wrench is
equipped with a protection system.
When the LED flashes for 3 seconds
and then goes out, the system will
automatically cut off the power to
extend battery life. If the machine
and battery pack are placed in the
following locations, the machine
may automatically power off during
operation:
• Overload: If the tool is overloaded, the
abnormally high current may be released;
in this case, release the switch on the tool
to stop the overloading operation; and then
restart.
• Overheat: When the above situations
occur, if the tool fails to start by pressing the
switch, the tool and battery will overheat.
In this case, cool the tool and battery pack
before starting the switch again.
• Low voltage: The tool does not work
when the remaining capacity is too low. In
this case, remove and replace the battery
pack.
WARNING:Press the switch to
ensure that the steering lever is
on both the left and right sides before
turning the LED on.
TROUBLE SHOOTING
1.I CAN NOT FIT THE BATTERY INTO THE
BATTERY CHARGER. WHY?
The battery can be inserted into the charger only in
one direction. Turn the battery around until it can be
inserted into the slot, the red LED Light should turn on
when the battery is charging.
2. REASONS FOR DIFFERENT BATTERY PACK
WORKING TIMES
Charging time problems, as above, and having not
used a Battery Pack for a prolonged time will reduce
the Battery Pack working time. This is the problem
related with the number of charging. Such situation
will be improved after charging and using for several
times. Heavy working conditions such as large screws
into hard wood will use up the Battery Pack energy
faster than lighter working conditions. Do not re-
charge your Battery Pack below 0
as this will affect performance.
MAINTENANCE
Remove the battery pack from the machine
before carrying out any adjustment, servicing or
maintenance.
Your power tool requires no additional lubrication or
maintenance. Never use water or chemical cleaners to
clean your power tool. Wipe it with a dry cloth. Wipe
clean with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots clean.
Keep all working controls free of dust.
FOR BATTERY TOOLS
The ambient temperature range for the use and stor-
age of tool and battery is 0°C-45°C.
The recommended ambient temperature range for the
charging system during charging is 0°C-40°C.
ENVIRONMENTAL
PROTECTION
See Fig. F
retailer for recycling advice.
DECLARATION OF
CONFORMITY
We,
Positec Germany GmbH
Grüner Weg 10, 50825 Cologne, Germany
Declare that the product
Description Battery operated impact wrench
Type designation KUB30 KUB30.2 KUB30.91
(B30-designation of machinery, representative
of impact wrench
Function Tightening and loosening screws, nuts
Complies with the following Directives:
2006/42/EC
2014/30/EU
2011/65/EU&(EU)2015/863
Standards conform to
EN 62841-1
EN 62841-2-2
EN 55014-1
EN 55014-2
The person authorized to compile the technical file,
Name Marcel Filz
Address Positec Germany GmbH
Grüner Weg 10, 50825 Cologne, Germany
C and above 30 C
o o
2020/05/25
Allen Ding
Deputy Chief Engineer, Testing & Certification
Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities or
9
EN