Protecting The Environment - Black+Decker BEH200 Manual De Instrucciones

Rotate the side handle into the desired position.
u
Insert the depth stop (not supplied) into the mounting hole.
u
Set the drilling depth as described below.
u
Tighten the side handle by turning the grip clockwise.
u
Fitting a drill bit
(fig. B)
Open the chuck by turning the front part with one
u
hand while holding the rear part with the other.
Insert the bit shaft into the chuck and firmly tighten
u
the chuck.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counter clockwise) rotation.
To select forward rotation, push the forward/reverse
u
switch (3) to the left position.
To select reverse rotation, push the forward/reverse
u
button to the right.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode (fig. D)
For Impact drilling in masonry and concrete, set the
u
drilling mode selector (4) to the
For drilling in steel, wood and plastics or for screw driving
u
set the operating mode selector (4) to the
Setting the drilling depth (fig. D)
Slacken the side handle (6) by turning the grip counter
u
clockwise.
Set the depth stop (not supplied) to the desired position.
u
The maximum drilling depth is equal to the distance be-
tween the tip of the drill bit and the front end of the depth
stop.
Tighten the side handle by turning the grip clockwise.
u
Switching on and off
To switch the tool on, press the variable speed
u
switch (1). The tool speed depends on how far you
press the switch. As a general rule, use low speeds
for large diameter drill bits and high speeds for smaller
diameter drill bits.
For continuous operation, press the lock-on button (2)
u
and release the variable speed switch. This option is
available only at full speed in both forward and reverse
modes.
To switch the tool off, release the variable speed switch.
u
q
position.
r
position.
(Original instructions)
To switch the tool off when in continuous operation,
press the variable speed switch again and release it.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Protecting the environment

Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries
according to local provisions.
Further information is available at www.2helpU.com
ENGLISH
5