Care And Maintenance; Troubleshooting - Harbor Breeze E-PAR52CB5C Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

CARE AND MAINTENANCE

At least twice each year, lower canopy (B) to check downrod (A) assembly, and then tighten all screws on the fan.
Clean motor housing (D) with only a soft brush or lint-free cloth to avoid scratching the finish. Clean blades (J) with
a lint-free cloth.
Important: Shut off main power supply before beginning any maintenance. Do not use water or a damp cloth to
clean the ceiling fan.
TROUBLESHOOTING (continued on next page)
Warning: Before beginning work, shut off the power supply to avoid electrical shock.
Problem
Fan does not move.
Noisy operation.
Excessive wobbling.
Fan operates but lights fail.
Lights dim when turning fan
and/or lights on.
Possible Cause
1. Reverse switch not engaged.
2. Power is off or fuse is blown.
3. Faulty wire connection.
4. Plugs not connected properly.
1. Blades (J) are loose.
2. Cracked blade (J).
3. Unapproved speed control.
1. Blades (J) are loose.
2. Blade arms (H) incorrectly attached.
3. Unbalanced blades (J).
4. Fan not securely mounted.
5. Fan too close to vaulted ceiling.
6. Set screw(s) on motor housing yoke
is (are) not tightened properly.
7. Set screw on hanging ball is not
tightened properly.
1. Bulb(s) not installed correctly.
2. Wires in canopy (B) not wired properly.
3. Wall switch to fan is off.
4. Wires in switch housing (E) not wired
correctly.
1. Fan is lamped with more than 190W
and fan was turned off at wall switch,
causing the wattage limiting device to
re-set itself.
2. Fan is lamped with more than 190W
causing the wattage limiting device in
fan to re-set itself due to power outage.
Corrective Action
1. Push switch firmly either way.
2. Turn power on or check fuse.
3. Turn power off. Loosen canopy (B) and
check all connections.
4. Check that male and female plugs in
switch housing (E) are connected properly
according to instructions on page 8.
1. Tighten all blade screws (L).
2. Replace blade (J).
3. Replace with an approved speed
control device.
1. Tighten all blade screws (L).
2. Re-install blade arms (H).
3. Switch one blade (J) with a blade (J)
from the opposite side.
4. Turn power off. Carefully loosen
canopy (B) and verify that mounting
bracket (C) is secure.
5. Use a longer downrod (A) or move fan
to another location.
6. Tighten yoke set screw(s) securely.
7. Carefully loosen and lower canopy (B)
and verify that set screw on hanging ball
is tightened securely.
1. Re-install bulb(s).
2. Check wires in canopy (B) and, if
necessary, re-wire according to
instructions on pages 6 and 7.
3. Make sure that wall switch to fan is on.
4. Check wires in switch housing (E) and,
if necessary, re-wire according to
instructions on page 8.
1. No action necessary--fan will automati-
cally re-set within 5 seconds after turning
wall switch back on.
2. No action necessary--fan will automati-
cally re-set within 5 seconds after turning
power back on.
Note: In order to avoid this problem, fan
may be lamped with bulbs totaling no
more than than 190W.
10

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

0065388

Tabla de contenido