Greenlee 855GX IntelliBENDER Manual De Instrucciones página 14

Operation (cont'd)
Fully Programmed Bending (cont'd)
6. Input the dimensions of the bend.
Stubs and kicks:
Press the button next to "HT" (height) if it is not
already highlighted with an asterisk. Use the buttons
next to +# and –$ to increase or decrease the height
until it is to the desired value. A single press of
the button will change the value by 1/8". Holding
the button down will rapidly change the values.
Press the button next to "A" (angle). Select the
desired angle as above. The angle changes in 1/2°
increments.
Offsets:
Press the button next to "HT" (height) if it is not
already highlighted with an asterisk. Use the buttons
next to +# and –$ to increase or decrease the height
until it is to the desired value. A single press of the
button will change the value by 1/8". Holding the
button down will rapidly change the values. Press
the button next to "L" (length). Select the desired
length as above. The length changes in 1/8" incre-
ments. Press the button next to "A" (angle). Select
the desired angle as above. The angle changes in
1/2° increments.
Saddles:
Press the button next to "HT" (height) if it is not
already highlighted with an asterisk. Use the buttons
next to +# and –$ to increase or decrease the height
until it is to the desired value. A single press of the
button will change the value by 1/8". Holding the
button down will rapidly change the values. Press
the button next to "L" (length). Select the desired
length as above. The length changes in 1/8" incre-
ments. Press the button next to "A" (angle). Select
the desired angle as above. The angle changes in
1/2° increments.
U-bends:
Press the button next to "HT" (height) if it is not
already highlighted with an asterisk. Use the buttons
next to +# and –$ to increase or decrease the height
until it is to the desired value. A single press of
the button will change the value by 1/8". Holding
the button down will rapidly change the values.
Press the button next to "L" (length). Select the
desired length as above. The length changes in 1/8"
increments.
3D bends:
A 3D bend is the same as an offset bend, except
there is an additional change of direction right and/
or left. Input the desired height by pressing the
button next to "HT" if it is not already highlighted
with an asterisk. Use the buttons next to +# and –$
to increase or decrease the height value. A single
Greenlee Tools, Inc.
855GX Electric Bender
press of the button will change the height by 1/8".
Holding the button down will rapidly change the
values. Select the rise angle by pressing the button
next to "A". Select the angle value as above. The
angle changes in 1/2° increments.
Select the horizontal bend angles by pressing the
button next to "H1" and adjusting the value as
above; repeat for the "H2" button. The horizontal
angles are as viewed from directly above. Refer
to the "Top Views of Bends" illustration below for
examples. Positive angles represent bends to the
right. Negative angles represent bends to the left.
Select the length by pressing the button next to "L".
Select the value for "L" as above. All values for "L"
are to the centerline of the conduit. The length is
defined as where the sight lines of the first and third
legs intersect each other to the end of the conduit,
as viewed from directly above. Refer to the following
illustrations for examples.
H1 = 45°
H2 = 90°
L
H1 = 90°
H2 = 90°
L
L
L
Top Views of Bends
14
4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
HT
A
H1 = –45°
H2 = –60°
L
H1 = 30°
H2 = –60°
H1 = 45°
H2 = 0°
H1 = 60°
L = ∞
H2 = 30°
L