Klippan Opti 129 Manual De Usuario página 7

Washing instruction
Rear-ward facing is safest!
Parts on the seat
1
Seat-cover
2 Insert
3
Internal 5P belt
4
Shoulder Pad
5 Buckle
6
Buckle Pad
7
Central Adjuster
8
Adjuster Belt
9 Seat-shell
10
Seatbelt attachement point
12
GB
11
Seatbelt tongue
12 Adjustment of headrest
13
Adjustment of shoulderstraps
14
User instruction
15 Adjustment of lower tether straps
16
Lower tether straps
17
Load leg
18
Locking for load leg
19 Adjustment of Recline
Instruction manual
Pull out the internal belt to full extent,
1
by pushing button (A) and pulling the
shoulder belts (B).
Release the shoulder belt pipe from the
2
back of the seat, move the pipe to the
new height and replace the pipe, push
one end of the pipe into the mount and
then press the other end of pipe into
the other mount.
Preparations to mount the seat into the car
Attach the lower tether straps to the
5
rails on the front seat of the car if the
strap can be threaded between the
floor and the rail.
Mounting of the lower tether straps on
6
the sides of the backseat.
Lower tether straps can be mounted to
7
the backrest of the front seat.
If there are no attachment points in
8
the car, you can use our additional
attachement loops. These can be
fastened into the car. Klippan item
number for these 150-55-706.
Check beneth the car seat if you can
9
use existing bolts for mounting the
additional attachement loops.
Mounting the lower tether straps
10
on the sides of the backseat, using
attachement loops.
Place the child seat on the seat of the
11
car. Adjust the reclining on the recline-
tube by pulling the adjustment button (1).
Pull out the leg, and lock the button (2).
Turn out the load-leg against the
12
stopper (1). Adjust the length on the
load-leg by pulling out the red button
on the side (2). Check that the load-
leg is properly against the floor of the
car, and that the load-leg is properly
locked (3).
Pull out completely the cars 3P seat
13
belt, thread the belt throug the blue
mounting hooks on the child seat.
Thread the cars 3P belt beneth the
14
cover of the childseat and lock the
tongue into the buckle. Tighten after
this first the lap belt and then the
shoulder belt as tight as possible.
13
GB
The shoulder straps should be at the
3
same level as the lower part of the head
support.
Pull the handle and adjust the height of
4
the headrest.
Thread the blue locking clip beneth the
15
cars 3P shoulder belt.
Tighten the shoulderbelt and lock the
16
blue belt-lock.
Check that the cars 3P seat belt is
17
mounted as shown on the image.
Attach the lower tether straps to the
18
child seat.
Tighten as tight as possible the lower
19
tether straps.
The buckle on the lower tether strap
20
can be loosen by lifting it up. The seat
can be dismounted in reversed order.
Placing in the middle of the back
21
seat. In some cars, the midle console
22
prevents the correct mounting of the
load leg. If the load leg cannot be
mounted like the image shows, the
seat cannot be mounted on this place
in the car.
Mounting the lower tether straps on the
23
passanger side.
24
The best way to mount the child seat in
25
front on the passanger side is to place
it against the dashbord, with help of the
load leg and recline tube. The child seat
can also be mounted to the frontseat,
with a 100mm space to the dashboard.
Please note, if placing the seat against
the dashboard, some scratches can be
caused by the metal parts. Please use a
soft towel to protect the dashboard.