Publicidad
Idiomas disponibles
Idiomas disponibles
AUTOMOTIVE PRODUCTS, INC.
ARTICLE
QUANTITE
1
2
2,3
2
4,5
2
6,7
2
8,9
2
10,11
2
12
2
13
4
14
4
15
4
16
4
17
4
18
8
19
8
20
8
21
8
22
4
23
8
24
8
25
4
26
8
27
2
28
2
29
2
1.
Remove contents from box verify all parts listed are present and free from damage. Carefully read and understand all instructions before
attempting installation.
2.
Starting at the front drivers side of the vehicle, remove the tape covering the factory oval holes in the inner body panel located by the
front tire, partially thread a plastic retainer onto the threaded end of a bolt/nut plate, insert it into the factory oval hole. Hold the bolt with
one hand and tighten the plastic retainer with the other until it is flush with the body panel.( Fig 1)
3.
Take (1) M12 bolt plate and partially thread a plastic retainer onto it. Insert the bolt plate into the forward, smaller oval hole and install as
per step 2.
4.
Take the front mounting bracket and position it onto the installed bolt plates, secure it with (2) M12 flat washers, (2) M12 lock washers
and (2) M12 hex nuts, do not fully tighten at this time. Rotate the bolt/nut plate until the threaded nut plate line sup with the remaining
hole in the mounting bracket and body. Thread (1) M10 x 35MM hex bolt, (1) M10 lock washer into the threaded nut. Do not fully
tighten at this time. (Fig 2)
5.
Remove the drivers side front factory body mount bolt and washer. Take the drivers side front support bracket. Insert the the factory body
bolt and washer through the slot in the support bracket and up into its original position. Line the other end of the support bracket up with
the oval hole in the front mounting bracket. Do not fully tighten at this time (Fig 2)
6.
Move to the middle of the vehicle on the drivers side and remove the tape covering the factory oval hole. Install a bolt/nut plate as per
step 2. (Fig 3)
7.
Take the drivers side center mounting bracket, position the mounting bracket onto the installed bolt/nut plate. Secure it with (1) M12 lock
washer, and (1) M12 hex nut. Do not fully tighten at this time. Rotate the bolt/nut plate until the nut lines up with the remaining hole in
the mounting bracket and body. Thread (1) M10 hex bolt, (1) M10 flat washer, and(1) M10 lock washer into the threaded nut. Do not
fully tighten at this time. (Fig 4)
8.
Move to the rear location and remove the tape covering the single factory hole. Take (1) M12 bolt plate and install it as described in steps
2 and 3. Select the drivers side rear mounting bracket position it onto the installed bolt plate secure it with (1) M12 flat washer, (1) M12
lock washer and, (1) M12 hex nut, push the bracket up against the body panel while tightening. (Fig 5, Fig 6)
9.
Remove the rear drivers side body mount bolt, take the rear support bracket, insert the factory bolt and washer through the rear support
bracket and install it up into its original position. Take (1) rear support strap and bolt it to the mounting tab on the rear support mounting
bracket to the rear mounting bracket with (2) M10 x 35MM hex bolts, (4) M10 x 20MM od flat washers, (2) M10 lock washers and (2)
M10 hex nuts do not fully tighten at this time. ( Fig 7)
Westin Automotive Products, Inc.
5200 N. Irwindale Ave. Ste 220
Irwindale, Ca 91706
INSTRUCTIONS—INSTRUCCIONES—CONSIGNES
Part # : 23-3570, 23-3575, 25-3570, 25-3575, 26-3570,21-3575, 21-3570
DESCRIPTION
BARRES LATERALES
SUPPORTS DE MONTAGE AVANT (2) COTE CONDUCTEUR, (3) COTE PASSAGER
SUPPORT DE FIXATION AVANT (4) COTE CONDUCTEUR, (5) COTE PASSAGER
SUPPORT DE MONTAGE CENTRAL (6) COTE CONDUCTEUR, (7) COTE PASSAGER
SUPPORTS DE MONTAGE ARRIERE (8) COTE CONDUCTEUR, (9) COTE PASSAGER
SUPPORTS DE FIXATION ARRIERE (10) COTE CONDUCTEUR, (11) COTE PASSAGER 16MM CLE
SANGLES SUPPORT ARRIERE
1/2" X 2" BOULONS HEXAGONAUX
1/2" RONDELLES-FREIN
1/2" RONDELLES PLATES
M12 X 35MM BOULON / M10 PLAQUE A ECROU
M12 X 40MM PLAQUES A BOULON
M12 RONDELLES PLATES
M12 RONDELLES-FREIN
M12 ECROUS HEXAGONAUX
M12 BUTOIRS PLASTIQUES
M10 X 30MM DO RONDELLES PLATES
M10 X 20MM RONDELLES PLATES
M10 RONDELLES-FREIN
M10 ECROUS HEXAGONAUX
M10 X 35MMBOULONS HEXAGONAUX
M8 BOULONS HEXAGONAUX
M8 RONDELLES PLATES
M8 RONDELLES-FREIN
APPLICATION: 2010 DODGE RAM 2500/3500 HD
75-1008 Rev B 8/10/12
OUTILS NECESSAIRES
3/4" DOUILLE ET CLIQUET
3/4" CLE
18MM DOUILLE ET CLIQUET
18MM CLE
16MM DOUILLE ET CLIQUET
13MM DOUILLE ET CLIQUET
13MM CLE
Thank You for choosing Westin products
For additional installation assistance please call
Customer Service (800)793-7846
W12-0996
Publicidad
