Declaration Of Conformity; Specified Use; General Safety Instructions; Special Safety Instructions - Metabo BE 18 LTX 6 Manual Original

en ENGLISH
Original Instructions
q
21q

1. Declaration of Conformity

We, being solely responsible, hereby declare that
these drills, identified by type and serial number *1),
meet all relevant requirements of directives *2) and
standards *3). Technical documents for *4) - see
page 3.

2. Specified Use

The drills are suitable for non-impact drilling in
metal, wood, plastic and similar materials.
Furthermore, the BE 600/13-2 is suitable for thread
tapping and screwdriving.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Instructions

For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference. Pass on your electrical tool only
together with these documents.

4. Special Safety Instructions

Use the side handle(s), supplied with the tool.
Loss of control can cause personal injury.
Mains powered machines: Hold the power tool
by insulated gripping surfaces, when
performing an operation where the cutting
accessory or fasteners may contact hidden
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
Cordless machines: Hold the power tool by
insulated gripping surfaces, when performing
an operation where the cutting accessory or
fasteners may contact hidden wiring. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
a) Never operate at higher speed than the
maximum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to rotate
10
freely without contacting the workpiece, resulting in
personal injury.
b) Always start drilling at low speed and with
the bit tip in contact with the workpiece. At
higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece,
resulting in personal injury.
c) Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage and loss of control,
resulting in personal injury.
Ensure that the place where you wish to work is free
of power cables, gas lines or water pipes (e.g.
check using a metal detector).
Smaller workpieces must be secured in such a way
that they are not carried along with the tool (e.g. by
clamping in a vice or on a work bench with screw
clamps).
Keep hands away from the rotating tool! Remove
chips and similar material only with the machine at
a standstill.
High forces are released if the tool jams or catches.
Always hold the machine with both hands by the
intended handles, take a secure stance and
concentrate on the work.
Caution must be exercised when driving screws into
hard materials (driving screws with metric or
imperial threads into steel)! The screw head may
break or a high reverse torque may build up on the
handle.
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- Crystalline silica from bricks and cement and
other masonry products, and
- Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.