Initial Operation - Metabo RSEV 17-125 Manual Original

en ENGLISH
20 Segment for working near walls (open by
twisting)
21 Brush rim
* depending on equipment/not in scope of delivery

6. Initial Operation

Before commissioning, check that the rated
mains voltage and mains frequency stated on
the type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
6.1 Attach the safety guard
See illustration D on page 3.
- Push and hold the lever (17). Place the safety
guard (18) in the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Make sure that the guard is placed securely: The
lever must engage and you should not be able to
turn the safety guard.
(Disassemble in reverse order.)
6.2 Dust extraction
Always use a suitable dust extraction system:
Connect an M-class vacuum cleaner to the
extractor connection piece (19).
For optimal dust extraction, use the connecting
sleeve 6.30796.
We recommend using an antistatic suction hose
Ø 35 mm.
7. Attaching the accessory
Prior to any conversion work: pull the mains
plug out of the socket. The machine must be
switched off and the spindle at a standstill.
7.1 Locking the spindle
Press in the spindle locking knob (1) only
when the spindle is stationary!
- Press in the spindle locking button (1) and
turn the spindle (7) by hand until the spindle
locking button engages.
7.2 Fitting/removing the diamond cup wheel
See illustration A on page 3.
To fit:
- Fit the support flange (8) on the spindle (7). The
flange should not turn on the locked spindle when
properly attached.
- Lay the diamond cup wheel (9) on the support
flange so (8) that it lies flat along the support
flange.
- The 2 sides of the clamping nut (10) are different.
Screw the clamping nut onto the spindle so that
the band of the clamping nut (10) is facing upward.
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (10) clockwise using the 2-hole
spanner (11) to secure.
14
Removal:
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (10) anticlockwise using the 2-hole
spanner (11) to unscrew.
7.3 Fitting/removal of backing pad for fibre
discs
See illustration B on page 3.
To fit:
- Fit the support flange (8) on the spindle (7). The
flange should not turn on the spindle when
properly attached.
- Lock the spindle (see chapter 7.1).
- Fit the backing pad (12) on the spindle (7).
- Put on the fibre disc (13).
- Screw the special clamping nut (14) onto the
spindle (7) as follows.
- Turn clockwise using the 2-hole spanner (11).
Removal:
- Lock the spindle (see chapter 7.1).
- Turn anticlockwise using the 2-hole spanner (11).
7.4 Fitting/removal of the cling-fit backing
pad
See page 3, figure C.
To fit:
- Remove support flange and put aside.
- Lock the spindle (see chapter 7.1).
- Screw the cling-fit backing pad (15) onto the
spindle and tighten by hand.
Removal:
- Lock the spindle (see chapter 7.1).
- Turn the cling-fit backing pad (15) anticlockwise
by hand to unscrew.
8. Use
Always guide the machine with both hands on
the handles of the angle grinder provided.
8.1 Working close to walls
See illustration E on page 3.
To open and close the segment (20) switch off
the machine and pull the mains plug. The
accessory must be stationary.
Only open the segment (20) by twisting when
working close to walls. For all other work, the
segment must be lowered.
The open area of the safety guard must face the
direction of the wall.
8.2 Setting speed
Set the optimum speed on the setting wheel (6),
depending on the application.
8.3 Switching on and off
Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.