Additional Safety Instructions - YATO YT-82144 Manual De Instrucciones

GB
closed areas. Using a correct extension cord permits to reduce the risk of an electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RDC) protected supply. Use of
an RCD reduces the risk of electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are
tired or under eff ects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries.
Always use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks,
protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries.
Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool to the
mains. Holding the tool with a fi nger on the switch or connecting an electric tool when the switch is in the ON position may lead
to serious injuries.
Before you turn an electric tool on remove all the spanners and other tools, which have been used for adjustments. A
spanner left on rotating elements of the tool may lead to serious injuries.
Keep your balance. Maintain an appropriate position. It will permit to control the electric tool in case of unpredicted situations
during its operation.
Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes and gloves away from moving
elements of the electric tool. Loose clothes, jewellery or long hair may get caught on moving elements of the tool.
Use dust extractors or dust containers, if the tool is equipped with any. Make sure they are properly connected. Using of
dust extractors permits to reduce the risk of serious injuries.
Operation of the electric tool
Do not overload the electric tool. Use a proper tool for the given purpose. A correct selection of the tool for the given work
will result in a more effi cient and safer work.
Do not use the electric tool if the switch is not functioning properly. A tool which may not be controlled by means of a switch
is dangerous and must be repaired.
Disconnect the plug from the mains socket before any adjustment, replacement of accessories or storage of the tool. It
will permit to avoid accidental activation of the electric tool.
Store the tool away from children. Do not allow untrained persons to operate the tool. An electric tool may be dangerous
in hands of an untrained person.
Make sure the tool is properly maintained. Check the tool in order to detects any unfi tting or loose moving elements.
Check whether the elements of the tool are not damaged. In case any damaged elements of the tool are detected, they
must be repaired before the electric tool is operated. Many accidents are caused by improper maintenance of tools.
Cutting tools must be sharp and clean. Properly maintained cutting tools are easier to control during work.
Use electric tools and accessories in accordance with the aforementioned instructions. Use the tool in accordance with
its purpose, taking into account the kind and conditions of work. Should the tool be used for other applications than the ones
it has been designed for, the risk of a dangerous situation increases.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee
a proper level of safety of operation of the electric tool.

ADDITIONAL SAFETY INSTRUCTIONS

Do not put the tool down before the knife stops. An exposed rotating knife may „catch" the ground and impede the control of
the tool and cause serious injuries.
Hold the tool only by the insulated surfaces, since the cutting element may touch the power supply cable of the tool. If the
cable is cut, the metal elements of the tool might become live, which might cause electric shock to the operator.
Use clamps or other elements to fi x the processed element to a stable surface. If the processed material is held with a hand
or another part of the body, the tool is not stable and the operator may lose control over it.
INSTALLATION OF WORKING ELEMENTS
Attention! Installation of the accessories must be realised with the power supply off (Remove the plug of the cord of the grinder
from the socket!!
Attention! It is always required to replace all the knives the plane is equipped with. It is prohibited to operate the tool, if not all the
knives are installed. The drum rotates at a high velocity and it is adequately balanced for operation with all the knives installed. If
not all the knives are installed, the plane may be damaged during operation, which may cause serious injuries.
Replacement of the power transmission belt
Remove the protection of the power transmission belt (II). Lift the edge of the belt with a wide and plane screwdriver close to the
O R I G I N A L I N S T R U C T I O N S
13