3M PELTOR WS LiteCom Pro III MT73H74D10EU Serie Manual Del Usuario página 4

GB
This product contains electrical and electronic
components and must not be disposed of using standard
refuse collection. Please consult local directives for disposal
of electrical and electronic equipment.
1. APPROVALS
3M Svenska AB hereby declares that this 3M™ PELTOR™
Headset is in compliance with the essential requirements and
other provisions set out in the appropriate directives. Thereby
they fulfil the requirements for CE marking.
Hereby, 3M Svenska AB declares that the radio equipment
type two-way radio is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at
the following internet address: http://www.3M.com/PELTOR/doc
The product has been tested and approved in accordance
with EN 352-1:2002 / EN 352-3:2002, EN 352-4:2001/
A1:2005, EN 352-6:2002, EN 352-8:2008.
Additional information can be obtained by contacting 3M in
the country of purchase or 3M Svenska AB Värnamo. For
contact information, see last pages of this user instruction.
Upon request, type in your part number. The part number of
your earmuffs can be found on the label of one cup as seen
in the picture below.
Notified Body Statement of Opinion offered by:
FIOH, Finnish Institute of Occupational Health, Topeliuksen-
katu 41 a A, FI-00250, Helsinki, Finland. Notified body #0403.
2. LABORATORY ATTENUATION
WARNING! 3M strongly recommends individual fit testing of
hearing protectors. If the SNR is used to estimate typical
workplace protection, 3M recommends that the noise
reduction value be reduced by 50% or in accordance with
applicable regulations.
A. Explanation of attenuation tables:
EN 352-1/ EN 352-3/ EN 352-4
A:1 Frequency (Hz)
A:2 Mean attenuation (dB)
A:3 Standard deviation (dB)
A:4 Assumed protection value, APV (dB)
A:5
H = Hearing protection estimation for high frequency sounds
(ƒ ≥ 2000Hz).
M = Hearing protection estimation for medium frequency
sounds (500Hz < ƒ < 2000Hz).
FP3806_rev_a.indd 3
L = Hearing protection estimation for low frequency sounds
(ƒ ≤ 500Hz).
A:6 Criterion Level
H = Criterion level for high-frequency noise
M = Criterion level for medium-frequency noise
L = Criterion level for low-frequency noise
*Criterion Levels chart is for level-dependent headsets, EN 352-4:2001/
A1:2005
B. Compatible Industrial Safety Helmets EN 352-3
These earmuffs should be fitted to, and used only with, the
industrial safety helmets listed in Table C. These earmuffs
were tested in combination with the following industrial safety
helmets, and may give different levels of protection if fitted to
different helmets.
Explanation of the industrial safety helmet attachment table:
B:1 Helmet manufacturer
B:2 Helmet model
B:3 Helmet attachment
B:4 Head size: S = small, M = medium, L = large
For more information about 3M Safety Helmets, visit
TM
www.3M.com
C. Explaination of the electrical audio input level table
EN 352-6
C:1 Input signal level U (mV, RMS)
C:2 Mean sound pressure level (dB(A))
C:3 (dB(A))
STD Sound Pressure
C:4 Input signal level for which the mean plus one standard
deviation equals 82 dB(A)
3. COMPONENTS
Headband MT73H7A4D10EU
D:1 Headband (PVC, PA)
D:2 Headband wire (stainless steel)
D:3 Two-point fastener (POM)
D:4 Cushion (PVC foil and PUR foam)
D:5 Foam liner (PUR foam)
D:6 Cup (ABS)
D:7 Environmental microphone (PUR foam)
D:8 Speech microphone (ABS)
D:9 Antenna (PE, ABS, TPE)
D:10 Auxiliary Port (brass)
D:11 Li-ion battery (PC, ABS)
Headband MT73H7F4D10EU-50
D:12 Headband (TPE)
D:13 Headband wire (stainless steel)
Helmet attachment/Hardhat MT73H7P3E4D10EU*
D:14 Cup supporting arm (stainless steel)
Neckband MT73H7B4D10EU*
D:15 Neckband wire (stainless steel)
D:16 Neckband cover (PO)
3
2017-01-25 09:39:56