Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Structure Of Warnings
Caution
Type and source of danger.
Possible consequences of non-obser-
vance.
Measures to avoid danger.
Symbols On The Product
Be sure that you understand their meaning before opera-
tion
Electrical voltage
Read the operating instructions carefully.
CE compliant
The product corresponds to the prescribed
technical requirements in Europe.
Observe and comply with all local disposal
guidelines for all components of this equip-
ment and it's packaging.
2.2 Operator Training
The tightening system may only be put into operation,
adjusted and tested by personnel that have been trained
and qualified by employees of Apex Tool Group.
The tool has been preset by Apex Tool Group. Changes to
the default settings can only be made by a qualified
1)
employee
.
Additional information can be found in the Programming
Manual.
2.3 Intended Use
This product is part of the Cleco Production Tools' tighten-
ing system. It is intended for use in industrial fastening pro-
cesses. Only use the tool under the following conditions.
The user is liable for damage caused by improper use.
•
In conjunction with the components listed in the EC
Declaration of Conformity.
•
Under the prescribed environmental conditions.
•
With the recommended battery pack and charger.
•
Within the power range, which is specified in the techni-
cal data.
•
With equipment parameters set up properly.
•
In EMC Limit Class A (electromagnetic immunity for
industrial areas). For the currently observed EMC stan-
dards, see the EC Declaration of Conformity.
1.Qualified employees have the training and experi-
ence to identify potentially hazardous situations.
They can initiate appropriate safety measures and
are obliged to comply with regulations.
Apex Tool Group
DO NOT use the tool as a hammer.
DO NOT use a controller other than the one listed in
the EC Declaration of Conformity.
DO NOT use the tool in potentially explosive areas.
DO NOT use the tool in damp spaces or outdoors.
DO NOT disassemble or modify the tool.
2.4 Standards
It is mandatory that national, state, and local codes and
standards be followed. Other type-specific standards see
Technical Data.
2.4.1 FCC and IC compliance
This product complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this
product. Operation is subject to the following two condi-
tions:
•
this product may not cause harmful interference, and
•
this product must accept any interference received,
including interference that may cause undesired oper-
ation.
FCC Responsible party
Name: William Cain
Position: Director, R&D
Address: 670 Industrial Drive
Lexington, SC 29072
United States
Phone: +1 803 951 7558
Email: William.Cain@ClecoTools.com
This product has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
product is operated in a commercial environment. This pro-
duct generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications.
Operation of this product in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
2.5 General Power Tool Safety
Warnings
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injuries.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to mains-oper-
ated (corded) power tool or battery-operated (cordless)
power tool.
1 Work Area Safety
a) Keep your work area clean and well lit. Cluttered or
P2543BA | 2021-01
1
EN
7
Publicidad
Tabla de contenido
