Ammann APH 6530 Traducción Del Manual De Instrucciones Original página 33

Check protective devices and brakes for proper functioning prior to
operation.
When reversing, particularly on the edges and banks of ditches, as
well as in front of obstacles, the machine operator cannot fall or be
crushed.
Always keep a safe distance away from the edges and banks of
ditches and refrain from any actions which could cause the machine
to topple over!
Always control the machine, so that hand injuries through hard ob-
jects are avoided!
Always ascend slopes carefully in a direct path.
Reverse up steep slopes to prevent the machine from toppling over
on to the machine operator.
If faults on the safety devices or other faults detrimental to the safe
operation of the machine are noticed, operation of the machine must
be stopped immediately and the faults remedied.
When undertaking compaction work in the vicinity of buildings or
above pipelines and similar, check the effect of the vibrations on the
buildings and pipes and stop compaction work if necessary.
Parking the machine
Park the machine on a firm and level surface.
Shutdown the drive and secure it to prevent accidental movement
and unauthorised use. If available, close the fuel valve. Do not place
or store equipment with integrated moving gear on the chassis. The
moving device is intended only for transportation purposes.
Filling petrol
Only fill petrol by switched-off motor.
No open fire, do not smoke.
Do not spill any fuel, collect discharging fuel in a suitable container,
prevent fuel from seeking into the soil.
Ensure that the filler cap is tight.
Leaky fuel tanks constitute an explosion hazard and must therefore
be replaced immediately.
Maintenance and repairs
Observe the maintenance, inspection and adjustments and intervals
specified in the operating instructions, as well as the information for
part replacement.
Maintenance work must be undertaken only by qualified and
authorised persons.
Maintenance and repairs only by switched-off drive.
Only carry out maintenance and repairs when the machine is parked
on a firm and even surface and is secured to prevent it from rolling.
When changing larger assemblies and individual components, only
use suitable and perfectly functioning hoistings and lifting gears with
suitable loading capacity. Attach and secure parts on hoisting care-
fully!
Spare parts must comply with the technical requirements of the man-
ufacturer. Therefore only use original spare parts.
Hydraulic lines must previously be rendered pressureless, before
working on them. Hydraulic oil discharging under pressure can
cause serious injuries.
Work on hydraulic devices must be undertaken only by persons with
a special knowledge of hydraulics and the necessary experience!
Do not adjust pressure relief valves.
Drain hydraulic oil at operating temperature – caution risk of scalding!
Collect discharging hydraulic oil and dispose of the same in an envi-
ronmentally-friendly manner.
Do not start the motor when hydraulic oil has been drained off.
After completing all work (by pressureless system), inspect all con-
nections and bolted connections for leaks.
Inspect all hoses and bolted connections for leaks at regular intervals
and externally visible damage! Rectify any damage immediately.
Replace externally damaged hydraulic hoselines at regular intervals
(depending on time used), even when no safety-relevant faults are
visible.
Before working on the electrical system of the machine, disconnect
the battery and insulate by covering or remove.
Inspect the electrical equipment of the machine at regular intervals.
Faults such as loose connections, worn or scorched cables must be
immediately eliminated.
During transport, secure the battery to prevent it from tilting,
short-circuit, slipping and damage.
Dispose of used batteries in a proper manner.
Do not place any tools on the battery.
Handling acid-batteries
Transport filled batteries upright to prevent acid spillage.
Keep away from sparks, open fire and other sources of ignition.
Avoid contact of acid with skin and clothing. In case of contact, wash
off acid immediately with clear water and go to medical institution.
Properly refit and inspect all protective devices after maintenance
and repairs.
Testing
Road rollers, trench rollers and vibrating plates must be tested for
safety by an expert depending on the particular application and oper-
ating conditions as required, however at least once a year.
Disposal of the machine after finish of its service life
At disposal of the machine after finish of its service life, the owner is
obliged to comply with national regulations and laws on wastes and
protection of environment. Therefore we recommend in such cases
to contact the following:
•
professional specialized companies engaged in such activities
and having the relevant certificate
•
the manufacturers or contracting service organizations autho-
rized by him.
The manufacturer is not responsible for damages to health of owners
neither for damages to the environment in events of failing to comply
with above mentioned hygienic and ecological principles.
30
1. Safety regulations