Product Service - YATO YG-04250 Manual Del Usuario

GB
Guidelines for connecting the product to the power supply
Before connecting the product to mains, you should make sure that voltage, the frequency and the performance of the mains
correspond to the values on the rating plate of the product. Power cable plug must fi t into the mains socket. It is forbidden to alter
the plug.
The product must be connected directly to a single wall mains socket. it is forbidden to use extension cables, splitters, and double
sockets. Circuit power supply network must be equipped with a grounding conductor and protection for 16 A.
Avoid contact of the power cable with sharp edges and hot objects and surfaces. When the product is working, the power cable
must always be fully unwound, and its location should be set so, it would be no obstacle during the operation of the product. Plac-
ing the power cable can cause a tripping hazard. The power outlet should be located in such a place, that there would be always
possible to quickly disconnect the power cable plug. When disconnecting the power cable plug, you should always pull by the
plug housing, never by the cable.
If the power cable or plug is damaged, you should immediately disconnect them from the mains and contact authorized service of
the manufacturer for replacement. Do not use the product with a damaged cable or plug. The power supply cable or plug may not
be repaired in the event of a failure of these elements they should be replaced with any new ones, free from defects.

PRODUCT SERVICE

Installation, starting, and operation of the product
You should unpack the product, completely removing all the elements of the package. It is recommended to keep the packaging,
may be useful for later transport and storage of the product.
Choose the place of installation in accordance with the instructions, which are presented above.
Wash the product in accordance with the instructions from the point "Product maintenance".
The tank of water coat should be fi lled to the marked limit. In order to speed up the heating, you may fi ll the water tank with warm
water.
Mount the lid by inserting the hook of the hinge between the housing of the product, and the tank for food. Insert the tank into
the product housing The collar of the fully inserted tank should keep the lid hinge on the spot. Check whether the lid opens and
closes freely.
Fill the product with food in accordance with the presented guidelines.
Close the lid.
Make sure, that the knob of temperature regulator is in the "O - off " position and then insert the plug of thepower cable to the
mains wall socket.
Turn on the product by setting the knob to the desired temperature for food. The heating process is signaled by shining the control
light placed near the knob. The control light will switch off when the process of food heating is completed.
The product will automatically maintain the set temperature throughout the time of connection to the power supply.
Attention! Food in the boiling pot may be heated to a high temperature, be careful during the food serving in order to avoid
burns.
During operation, you should continuously control the level of food in the device, and to complement it when needed.
When you complete the operation, you should turn off the product by setting the temperature knob in the "O - off " position, Remove
the power cable plug from the mains socket, then empty the tank of the product and proceed to its maintenance.
Emptying the product of food
Attention! Before complete emptying the product of food, you should turn off the product, and disconnect the plug of power cable
from the mains socket. Allow the food to cool completely in the product before emptying the tank.
Remove the tank from the product, then empty it of the food.
Maintenance of the product
Due to the use of the product for the storage of food, the product should be carefully maintained. This will allow maintaining proper
hygiene. The product must be subjected to the maintenance after each use.
Before each cleaning, turn off the product, disconnect the plug of the power cable from the mains wall socket, wait it cools down,
empty it of the food and only then proceed to maintenance. We recommend that you clean the product immediately after use.
Dried food is harder to remove from the product.
To clean the product, you should use only mild agents intended to clean kitchen utensils. It is forbidden to use abrasive clean-
ers, for example powder or cleaner milk, which is containing corrosive substances. Do not use cleaning solvents, gasoline or
alcohols.
The cleaner should be diluted with water according to the information that came with it, then apply on a soft cloth and clean the
product from inside and outside.
The tank, after its removing from the product, can be cleaned with water or in the dishwasher. Before installing the product again,
it must be thoroughly dried.
Residues of the cleaning agent should be removed from the outside with a soft cloth soaked in water, then wipe it dry. The Interior
of the product should be rinsed with clean water and dry or let to dry.
O R I G I N A L I N S T R U C T I O N S
8