Remote Control Programming - Comunello QUAD 24V 2M ONE Instrucciones De Uso

1 2 3 4 5 6 7 8 9 10
Programming buttons
AUTOSET Maximum Stroke Programming
NOTE: Always check operator rotation direction (Operator 1 and
Operator 2) and opening priority (which operator must start first)
before running the maximum stroke self-learning procedure. It is also
recommended that you start the self-learning process with the gate
half open.
NOTE: Before you start the operators moving for the system's
acquisition of the maximum stroke, the control unit screens the
system for any accessories installed on the digital BUS line. This
operation can introduce delays before the operators actually move.
NOTE: To check the correct programming of the stroke, you can
also use the STEP BY STEP button as AUTO-PP command (open-
close).
NOTE: During the maximum stroke self-learning procedure, make
sure that the operating leaf is free.

REMOTE CONTROL PROGRAMMING

Remote controls with different codes of either the fixed or rolling code
type can be saved on the control unit.
Programming:
Programming (and storage) of the transmission code is done
by pressing the TX CODE button and checking the status of the
corresponding LED (above the TX CODE button) as follows:
1. Press the TX CODE button once: the corresponding led lights
up and flashes once (1010). By sending the code of a transmitter
button, if the code is valid, it will be saved with AUTO-PP function
(open-close).
2. Press the TX CODE button twice: the corresponding led lights up
and flashes twice (110110). By sending the code of a transmitter
button, if the code is valid, it will be saved with PED function
(pedestrian).
3. Press the TX CODE button three times: the corresponding led
lights up and flashes three times (11101110). By sending the code
of a transmitter button, if the code is valid, it will be saved with AUX
function (2nd auxiliary channel).
Deletion:
Deletion of all the radio codes is done by pressing the TX CODE
button and checking the status of the corresponding LED (above the
TX CODE button) with the following association:
1. Press the TX CODE button four times: the corresponding led
lights up permanently (steady). To confirm the deletion, press the TX
CODE button again (the corresponding led starts to flash) and keep
it pressed until the led stops flashing, which confirms the successful
deletion of all codes saved in the system.
1 2 3 4 5 6 7 8 9 10
Programming buttons
TX CODE Remote control programming
ACCESSORIES DETECTION (BUS LINE)
The control unit automatically detects all the ONE accessories wired on
the BUS line, checking the type of accessory, its numeric identifier ID and
the type of operation set (MODE). Always make sure to use accessories
with different ID for each type of accessory (par: ACCESSORY ADDRESS
ASSIGNMENT). The system also detects the accessories installed on the
BUS line:
1 Before the maximum stroke self-learning process (AUTOSET). At this
stage, the system detects the accessories installed and saves the
system configuration (e.g.: new installation).
2 Each time you press the RESET button. At this stage, the system re-reads
the accessories installed, but does not change the initial configuration
(accessories saved).
NOTE: The detection of the accessories is an automatic operation that may
cause a delay in the system's configuration proportionate to the number
of accessories installed.
NOTE: Make sure you have set the ID and MODE (operating mode) on all
accessories installed, before connecting them to the digital BUS line.
IMPORTANT! If you want to configure the system with ONE app
access (requires the use of tablet with wireless connection and a
K-ONE access key - code ONE KEY), keep the MODE dip-switches
set to OFF (TYPE 1 operation) for all accessories connected to the
BUS line.
ADJUSTMENTS FROM COMUNELLO ONE APP
The control unit features an advanced access for additional system
configuration. Using the (optional) accessory K-ONE (code ONE KEY),
you can connect to the control unit via Wi-Fi radio and proceed to its full
configuration following a simple and guided procedure, with the aid of the
COMUNELLO ONE app that you can download from our online store.
To use the app COMUNELLO ONE, you will need a wifi device (tablet or
smartphone) with android or iOS operating system.
Connector for K-ONE module
Configuration via the COMUNELLO ONE app allows you to configure and
adjust all the parameters of the system in a fast and easy way, monitor its
operation, manage the list of saved remote controls, copy the configuration
to another equivalent system and plan maintenance.
ADDITIONAL ADJUSTMENTS FROM THE APP:
Guided procedure to check direction of rotation of the operators and
change their settings.
Commands
1 2 3 4 5 6 7 8 9 10
Set the pause time (automatic closing)
Enable Permanent Close.
Force/Speed
Adjust maximum operator speed during opening cycle
(10%..100%)
Adjust maximum operator speed during closing cycle (10%..100%)
Adjust deceleration speed during opening cycle
Adjust deceleration speed during closing cycle
Start Operator 1 deceleration during opening cycle
Start Operator 1 deceleration during closing cycle
Start Operator 2 deceleration during opening cycle
Start Operator 2 deceleration during closing cycle
Adjust pedestrian opening
Enable/Disable Operator Brake
Enable/Disable Soft Stop
Enable/Disable Soft Start
COMUNELLO ®Copyright 2015 - All right reserved
(0"..40 min)
(10%..100%)
(10%..100%)
( 0%..100%)
( 0%..100%)
( 0%..100%)
( 0%..100%)
(10%..100%)
33