Turning The Iron On - Leifheit Air Active L Professional Manual Del Usuario

Implementation
B
Preparation
I
To ensure that enough ventilation is available, the
back of the equipment must be at least 15 cm and
the sides at least 15 cm away from the wall or other
objects.
The complete system must be set up on a solid flat
surface!
When folded the system can be easily moved
to the desired position using the casters [7].
Pull the system along, do not try to push.
1. Remove the cord to the complete system [1] and
carefully move the pedestal forward. The complete
system folds out and you can then stop it at the
desired position. Then, you can move the complete
system forward and lower it onto the ground.
In the unfolded condition gently lift the pointed
end of the ironing board, then pull the system
along on the castors.
2. The complete system can be adjusted in height to
six different levels (maximum height
approx. 100 cm) and this makes it possible to
iron either standing up or sitting.
To adjust the height, hold the ironing board with
both hands, lift the ironing table gently and lift up
the activation lever (5) with one hand (the slight
lift on the ironing table is intended as a safety
measure to prevent unintended activation). As
soon as you hear an audible click, you know that
the ironing table is locked in place again.
Using the adjustable foot caps (6), you have the
option to compensate for any unevenness of the floor.
3. Set down the steam iron exclusively on the silicon
mat (14) that is part of the complete system.
4. The cable holder (22) should be clipped onto the
mount supplied for this purpose on the railing of
the complete system.
5. Insert the connection hose (15) into the cable
holder.
Information about filling the steam system:
Either cold or hot mains water can be used.
(max. 35 °C)
To increase the lifetime of your complete pressure
iron system you should always use additional distilled
water.
Hard water in particular (water containing calcium)
makes the use of distilled water necessary.
18
Filling with water
II
(before ironing)
1. Pull the water container [19] backwards along the
track.
2. Fill the water container to the maximum level
(see MAX marker on the scale).
(see information about filling the steam station on
page 19)
With some pressure, slide the water reservoir [19]
back into its original position. The reservoir is correctly
positioned only after an audible double clicking and
hushed acoustic signal. For a secure connection to the
housing, press the tank once again on the right-hand
rear side.
If you are using the equipment for the first time or
after decalcification, a particularly large amount of
water will be pumped into the steam station from the
removable water container. For this reason, refill the
tank if required.
Avoid over-filling the steam station (max. 800 - 900
ml). If the container is too full, hot water maybe
ejected rather than steam.
If water escapes or if the tank is too full, please pour
some water out and dry the equipment thoroughly.
For technical reasons the unit is equipped with a
pump. At irregular times this pump moves water as
necessary from the removable tank to the boiler and
facilitates uninterrupted, convenient ironing.
Your water supplier will be able to inform you about
the water hardness in your household.
When using distilled water, mains water needs to be
mixed in (mixture ratio 1:1).
Do not use any decalcifying or chemical substances or
ironing water additives in the water! This will damage
the steam system and steam iron.
Power supply
III
1. Connect the feed cable plug [9] of the steam iron
station to the socket [2] of the ironing board.
This will ensure that the steam iron station
is supplied with power.
2. Then connect the feed cable plug [1] for the
complete system to a wall socket.
Ironing procedure
IV
1. 1. Turn on the iron and steam system switch
[10] on.
Please keep in mind:
The steam system must only be used if there is enough
water in the steam system (but max. 800 - 900 ml).
We therefore recommend topping up the water before
each ironing session. In this way, you will avoid delays
while you refill the container during ironing.
Wait for a few minutes until the warning light
turns on to show that the steam is ready [12].
2. Then turn on the on/off switch [3] for the steam
extraction on the ironing board.
The steam extraction should be on constantly
whenever possible to remove excess steam from
the ironing board and the inside of the casing. This
ensures that the ironing board remains warm and
dry. (Please refer to the instructions for extraction
and air intake function on page 20).
3. Set the temperature control [16] on the steam
iron to the desired level.
Make sure that the set temperature of the iron
does not fall below the marker while ironing
with steam.
As soon as the control light [18] turns off, the
steam iron is ready for use.
4. Steam will then be released from the iron sole
when you press the steam button [17].
Make sure you always check the ironing instructions
on your clothing labels.
Protection of your clothes and optimal ironing results
are only guaranteed if the special Leifheit ironing
board cover for AirActive ironing boards is used.