Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Product Safety Information
Intended Use:
These Cordless Ratchet Wrenches are designed to remove and install threaded fasteners.
⚠
WARNING: Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
• Responsibly recycle or dispose of Batteries. Do not puncture or burn Batteries. Improper disposal may endanger the environment or
cause personal injury.
• Only use Tools with appropriate voltage Ingersoll Rand Batteries and Charger. Use of any other batteries may create a risk of fire,
personal injury or property damage.
For additional information, refer to Cordless Ratchet Wrench Safety Information Manual Form 80232929, Battery Charger Safety
Information Manual Form 10567832 and Battery Safety Information Manual Form 10567840.
Manuals can be downloaded from ingersollrand.com
Product Specifications
Voltage Battery
Tool
Model
Model
V, DC
BL2005
BL2012
R3130
20
BL2010
BL2022
BL2005
BL2012
R3150
20
BL2010
BL2022
† K
= 3dB measurement uncertainty
pA
‡ K
= 3dB measurement uncertainty
wA
*K = Vibration measurement uncertainty
Conforms to UL STD. 62841-1 & 62841-2-2.
Certified to CSA STD. C22.2 No. 62841-1 & 62841-2-2.
4004004
When using this product as a manually-operated ratchet wrench, do not exceed the maximum torque listed in the table. Exceeding this
torque may cause damage to the product and will void the warranty.
Product Operation
These models feature a variable trigger and an automatic shut-off.
The variable trigger feature allows an operator to regulate the power output of the tool through manipulation of the trigger lever. Power output
will increase as the trigger lever is pressed in, with maximum power output occurring when the trigger lever is fully depressed. Power output
will decrease as the trigger lever is released.
The automatic shut-off feature shuts off power to the motor when the motor is stalled. When tightening a fastener, the motor will stall when the
tool is unable to tighten the fastener any further, so automatic shut-off will occur at this condition. When attempting to loosen a fastener, the
motor will stall if the tool is unable to move the fastener, so automatic shut-off will occur at this condition also. When automatic shut-off occurs,
the trigger lever must be fully released and then pressed again to restart the tool. After automatic shut-off occurs, the tool can continue to be
used as a manually-operated ratchet, provided that the maximum torque limit specified for that particular model is not exceeded.
Lubrication
Maintenance frequency is shown in a circular arrow and defined as h=hours, d=days and m=months of actual use.
30d
1
2
3m
(Dwg. 48623839)
Parts and Maintenance
All other maintenance and tool repair should only be carried out by an authorized Service Center. For the nearest location, visit ingersollrand.com
Refer all communications to the nearest Ingersoll Rand office or distributor.
48621270_ed7
No Load
Recommended
Drive
Speed
Torque Range
inch
rpm
ft-lb (N-m)
3/8
0-225
10-45 (14-61)
3/8
0-225
10-45 (14-61)
1/2
0-225
10-45 (14-61)
1/2
0-225
10-45 (14-61)
3
6m
IR #
70
Inject between ratchet
housing and yoke to
lubricate drive bushing.
WARNING
Sound Level dB(A)
Max. Torque
ft-lb (N-m)
† Pressure (L
54 (73)
86
54 (73)
86
54 (73)
86
54 (73)
86
NOTICE
1
2
cm
IR #
3
1
70
Disassemble ratchet head
and lubricate components.
Vibration (m/s
(EN60745)
(EN60745)
)
‡ Power (L
)
Level
p
w
97
3.2
97
2.7
97
2.8
97
2.5
3
cm
IR #
3
2
67
Disassemble gearing and
lubricate components.
EN
)
2
*K
1.0
0.7
0.7
0.7
cm
3
1
EN-1
Publicidad
Tabla de contenido
