Cleaning And Maintenance; Technical Data - Adler europe AD 4221 Manual De Uso

ASSEMBLY WAY: Grinder function
1.Place the bowl (4) on the motor housing (2) and close the housing arm (1) by pressing the tilt knob (7). Do not assemble any
attachments inside the bowl (4). It is need to protect you against rotating of the mixer 's attachment nest with spring (18). It is normal
the mixer's attachment nest with spring (18) is rotating inside the bowl when using the mincer .
2.Take away the front cover (5) to set up the grinder.
3. Inside mincing chamber (17) place the worm gear (15), next place the mincing cross blade (14) correct. Take attention to place it
correct side, same as shown at picture C. Next, place the proper sieve (13) and LIGHTL Y screw the fixing nut (12) in the end.
REMARK: the fixing nut (12) has to be screwed LIGHTLY BEFORE assemble the whole mincing unit to the motor housing (2). It is need
to adjust the position of hexagonal hole (picture D1) in mincing unit to the hexagonal shaft in motor housing (2).
4.Place the mincer's unit in the position shown at picture D3 (slope position), push it inside the motor housing (2) and turn left to vertical
position shown at picture D4. The black round button close to the mincer 's unit will come back to protrude position. Screw the fixing
nut (12) tightly now.
5. Mount the mincing tray (16) on the top of the mincing chamber (17).
6. To dismantle the mincer's unit, press the black round button act in the reverse order .
USAGE: Mixer function
• Kneading heavy dough (bread dough, yeast dough, etc.)
Assemble the dough hook (11). Put food ingredients inside the bowl. Suggested flour and water ration is: 5:3. Maximum flour quantity:
1500g. It is recommended to start kneading at speed 1 or 2 for not longer than 20 seconds continuously operation. Next, set up the
speed 3 and operate not longer than 4 minutes continuously at a time.
• Mixing light mixtures (mayonnaise, pancake batter, sponge cake, etc.)
Assemble the mixing beater (10). Put food ingredients inside the bowl to max ¾ high of the bowl. Switch on speed 3-4 and mix as long
need to achieve desired density. Use not longer than 4 minutes continuously at a time.
• Whipping (egg whites, cake creams, whipped cream, etc.)
Assemble the egg whisk (9).
For egg whites whipping: Put egg whites inside the bowl to max 24 eggs. Switch on speed 4-6 and mix, about 5 minutes until stif f. Mixing
time depends of the size of eggs.
For whipped cream: put at least 250ml of fresh cream (previously chilled in a refrigerator for at least 8 hours).. Mix it at speed 4 to 6 for
about 5 minutes. Do not exceed the quantity of ½ high of the bowl of poured fresh cream to keep enough space for whipped cream.
USAGE: Grinder function
1. Cut all foods into pieces (sinewless, boneless and fatless beef or pork is recommended, approximately size: (20 mm x 20 mm x 60
mm,) so that they fit easily into the mincing tube (17).
2. Plug in the device and switch on and then turn the speed control knob (8) to 4-6 speeds.
3. Feed food into the mincing tray (16). Use for it only the plastic pusher (6).
4. After use switch the device off and unplug it from the power supply.
5. Use no longer than 4 minutes continuously at a time.
6. The device is equipped in 3 sieves with holes diameter 3mm, 5mm and 7mm, chose suitable hole plate to your desired dish.
- 3 mm sieve - fine mesh for grinding to a fairly compact, uniform consistency . Perfect for stuffing and pâté.
- 5 mm strainer - medium mesh for grinding meat for minced cutlets, burgers, meatballs and fillings for dumplings, pancakes and tortillas.
By using this strainer you can also grind vegetables, hard cheese and even nuts.
- 7 mm strainer - thick mesh for grinding meat with a distinct structure. The strainer is intended for the production of sausages and
giblets.
OVERHEAT PROTECTION DEVICE
The device will switch off automatically after 15 minutes of continuous operation to protect the motor against overheating. There is need
to plug off the device and let it cool down before next use. The device when cooled down will operate normally.

CLEANING AND MAINTENANCE

1.Before cleaning the device, be sure the power cord unplugged from the power outlet and the speed control knob is on the "0" position.
Let the device cools down before cleaning.
2.Disassemble all accessories from motor housing (2). Do not clean the accessories while mounted on the machine's drive assembly .
3.Don't use aggressive detergents to clean the motor housing (2), as it may remove the informational graphic symbols such as: scale,
signs, safety marks, etc.
4.Do not wash the metal parts in dishwashers. Aggressive cleaning agents used in dishwashers cause the metal parts to turn black.
Handwash the metal parts using traditional washing-up liquid. Use soft brush.
5.Wipe the external parts with kitchen towel or soft cloth.
6. Do not use abrasive materials to clean the device.
7. Don't immerse the motor housing () in water or other liquids.

TECHNICAL DATA

Power supply: 220-240V ~50/60Hz
Power: 1200W
Max Power: 2200W
Stainless steel bowl 7 liters
Max operation time in one cycle: 15 minutes.
Minimum rest time between cycles: 10 minutes at least.
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
7