Helpful Tips & Suggestions - Honda GP160 Manual Del Propietário

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 49
SPARK PLUG
Recommended Spark Plug: BPR6ES (NGK)
The recommended spark plug has the correct heat range for normal
engine operating temperatures.
An incorrect spark plug can cause engine damage.
If the engine has been running, let it cool before servicing the spark
plug.
For good performance, the spark plug must be properly gapped and
free of deposits.
1. Disconnect the spark plug
cap, and remove any dirt from
around the spark plug area.
2. Remove the spark plug with a
21 mm spark plug wrench.
3. Visually inspect the spark
plug. Replace it if damaged or
badly fouled, if the sealing
washer is in poor condition, or
if the electrode is worn.
4. Measure the spark plug
electrode gap with a wire-type
feeler gauge. Correct the gap,
if necessary, by carefully
bending the side electrode.
The gap should be:
0.7 – 0.8 mm
5. Install the spark plug carefully
by hand, to avoid
cross-threading.
6. After the spark plug is seated, tighten with a 21 mm spark plug
wrench to compress the sealing washer.
When installing a new spark plug, tighten 1/2 turn after the
spark plug seats to compress the washer.
When reinstalling the original spark plug, tighten 1/8–1/4 turn
after the spark plug seats to compress the washer.
A loose spark plug can overheat and damage the engine.
Overtightening the spark plug can damage the threads in the
cylinder head.
7. Attach the spark plug cap to the spark plug.
W20EPR-U (DENSO)
SPARK PLUG WRENCH
SPARK PLUG CAP
SIDE ELECTRODE
0.7–0.8 mm
SEALING
WASHER
HELPFUL TIPS & SUGGESTIONS
STORING YOUR ENGINE
Storage Preparation
Proper storage preparation is essential for keeping your engine
trouble-free and looking good. The following steps will help to keep
rust and corrosion from impairing your engine's function and
appearance, and will make the engine easier to start when you use
it again.
Cleaning
If the engine has been running, allow it to cool for at least half an
hour before cleaning. Clean all exterior surfaces, touch up any
damaged paint, and coat other areas that may rust with a light film
of oil.
Using a garden hose or pressure washing equipment can force
water into the air cleaner or muffler opening. Water in the air
cleaner will soak the air filter, and water that passes through the
air filter or muffler can enter the cylinder, causing damage.
Fuel
Depending on the region where you operate your equipment, fuel
formulations may deteriorate and oxidize rapidly. Fuel deterioration
and oxidation can occur in as little as 30 days and may cause
damage to the carburetor and/or fuel system. Please check with
your servicing dealer for local storage recommendations.
Gasoline will oxidize and deteriorate in storage. Deteriorated
gasoline will cause hard starting, and it leaves gum deposits that
clog the fuel system. If the gasoline in your engine deteriorates
during storage, you may need to have the carburetor and other fuel
system components serviced or replaced.
The length of time that gasoline can be left in your fuel tank and
carburetor without causing functional problems will vary with such
factors as gasoline blend, your storage temperatures, and whether
the fuel tank is partially or completely filled. The air in a partially
filled fuel tank promotes fuel deterioration. Very warm storage
temperatures accelerate fuel deterioration. Fuel deterioration
problems may occur within 30 days from keeping the fuel in the
fuel tank, or even less if the gasoline was not fresh when you filled
the fuel tank.
Fuel system damage or engine performance problems resulting
from neglected storage preparation are not covered under the
Warranty.
ENGLISH
11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Gp200

Tabla de contenido