Register Your Product - Southwire M400TP Instrucciones De Uso

Operation
Using the Tone Generator to Trace a Data Cable cont.
4. The pins the tone is being sent through will be shown on the bottom
of the LCD display. Repeatedly press the MODE button with short presses
to select the desired pins. Refer to sequence chart (B) below for explanation
of pin selection.
5. To turn off the tone generator, press and hold the MODE button.
Release the button as soon as OFF appears on the display.
(B)
1 2 3 4 5
1 2 3 6 4 5
1 2 3 4 5 6 7 8
NOTE:
When tracing a cable run from the tone generator to the end of the
cable, applying the tone on a single pin will allow the tone to be detected at a
greater distance from the cable. When trying to locate a cable in an equipment
room or patch panel, sending the tone through all 8 pins or a single pair will limit
the tone signal from spreading to other nearby cables. The tone will be loudest
when the probe tip is placed directly on the wires the tone is being sent through
at the end of the cable. When sending a tone through a single pair, verification
can be made by shorting the suspected pair. The tone will be very faint when the
pair the tone is being sent through is shorted.
6 7 8
Tone will be sent through
selected pin
Tone will be sent through
7 8
selected pair
Tone will be sent
through all 8 pins
9
Operation
Battery Replacement
1. Loosen and remove
the one Phillips screw.
2. Open the battery
compartment.
3. Replace the two
AAA batteries.
4. Re-assemble the meter.
NOTE:
Do not operate the tester with the battery door removed.

REGISTER YOUR PRODUCT

Register your product purchase at www.southwiretools.com or by scanning the QR code on this
manual. At Southwire, we are dedicated to providing you with the best customer experience. By
following a few quick steps to register, you can experience quicker service, more efficient support,
and receive information on our future products. Simply provide your model number, serial number,
and just a few pieces of information about yourself – it is that quick and easy.
LIMITED WARRANTY AND LIMITATION OF LIABILITY ON SOUTHWIRE METERS & TESTERS
Southwire Company, LLC warrants this product to be free from defects in material and
workmanship for two years from the date of purchase. This warranty does not cover fuses,
disposable batteries, or damage arising from an accident, neglect, misapplication,
contamination, modification, improper maintenance or repair, operation outside of specifications,
or abnormal handling of the product. Southwire's sole liability, and the purchaser's exclusive
remedy, for any breach of this warranty is expressly limited to Southwire's repair or replacement
of the product. Whether Southwire repairs or replaces the product will be a determination that
Southwire makes at its sole discretion. SOUTHWIRE MAKES NO WARRANTY THAT THE
PRODUCT WILL BE MERCHANTABLE OR FIT FOR ANY PARTICULAR PURPOSE.
SOUTHWIRE MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, OTHER THAN THE
WARRANTY SPECIFICALLY SET FORTH HEREIN. SOUTHWIRE WILL NOT BE LIABLE FOR
ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES FOR
ANY BREACH OF THIS WARRANTY.
This warranty is void if this product is used for rental purposes. No product reseller is authorized
to extend any other warranty on Southwire's behalf relating to this product, and no such reseller
warranty will be binding on Southwire. If you have a warranty claim, or if the product needs to
be serviced during or after the warranty period set forth above, please contact the Customer
Service Department at 855-SWTOOLS (855-798-6657). The sender is responsible for all
shipping, freight, insurance, and packaging costs associated with sending a product to
Southwire. Southwire will not be responsible for lost or damaged products returned pursuant
to this warranty. All products returned to Southwire under this warranty should be mailed to:
Southwire Company, LLC
Attention: Tool Warranty Return
5810 Trade Center Court
Villa Rica, GA 30180-6701
Phillips
Battery
screw
door
10