Operation - Craftsman 315.CR2100 Manuel Del Operador

aTTaCHING THe HIGH VeLOCITY NOZZLe
See Figure 2.
 Install the high velocity nozzle onto the end of the lower
blower tube as shown.
:
warNING
Do not allow familiarity with this
product to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
serious injury.
:
warNING
Always wear eye protection with side
shields marked to comply with ANSI Z87.1, along
with hearing protection. Failure to do so could result
in objects being thrown into your eyes and other
possible serious injuries.
:
warNING
Do not use any attachments or
accessories not recommended by the manufacturer
of this product. The use of attachments or
accessories not recommended can result in serious
personal injury.
:
warNING
Blower is intended for household use only.
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call 1-800-932-3188 or contact an
authorized service center for assistance.
appLICaTIONS
You may use this product for the purposes listed below:
 Clearing hard surfaces such as driveways and
walkways
 Keeping decks and driveways free from leaves and
pine needles
For complete charging instructions, refer to the Operator's
Manuals for your Craftsman
charger models.
TO INSTaLL / reMOVe BaTTerY paCK
See Figure 3.
warNING:
Always remove battery pack from the
product when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that
could cause serious personal injury.
All manuals and user guides at all-guides.com
aSSeMBLY

OperaTION

19.2 V battery pack and
®
 Slide the high velocity nozzle forward until notch locks
into place through the opening in the high velocity
nozzle.
To install:
 Place the power switch in the OFF ( O ) position.
 Place the battery pack in the blower. Align raised rib on
battery pack with groove in the blower's battery port.
 Make sure the latches on each side of the battery pack
snap in place and that the battery pack is secured in
the hedge trimmer before beginning operation.
CaUTION:
tool, be sure raised rib on battery pack aligns
with the bottom of the tool and latches into place
properly. Improper installation of the battery pack
can cause damage to internal components.
To remove:
 Place the power switch in the OFF ( O ) position.
 Locate the latches on the side of the battery pack and
depress both sides to release the battery pack from the
hedge trimmer.
 Remove battery pack from the blower.
C3 eNerGY INdICaTOr wINdOw
See Figure 3.
The C3 energy indicator window located on the side of the
handle, just above the base, will light when the 113710
Craftsman 19.2 V lithium-ion battery pack is installed and
has charge.
NOTe: Feature will not light with Craftsman 19.2 V nickel-
cadmium battery packs.
BaTTerY prOTeCTION FeaTUreS
Craftsman 19.2 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to stop
running. To reset the battery and tool, place the power
switch in the OFF position; then start the unit and resume
normal operation.
If placing the power switch in the OFF position does not
reset the battery and tool, the battery pack is depleted.
8 — English
When placing battery pack in the