YATO YT-82171 Manual De Instrucciones página 14

GB
Wear adequate clothing. Do not wear loose clothes or jewellery, since they might get caught by the moving elements of the tool.
It is recommended to use protective shoes with an anti-slip sole. Long hair must be placed completely under a cap or a protective
beret.
Use individual means of protection. Wear glasses or protective goggles. Wear dust masks during tasks which generate dust.
Connect dust extractors. If the tool is equipped with an extractor and dust container connection, make sure the aforementioned
elements are connected and are properly used.
Do not overload the power supply cord. Do not remove the plug from the socket pulling the power supply cord. Do not place the
power supply cord close to sources of heat, oil and sharp edges.
Safe work. Whenever possible, it is required to use clamps or anvils to fix the material to be processed. Such fixing is safer than
holding it with your hand.
Do not overreach. Maintain adequate position and equilibrium throughout the work.
Provide adequate maintenance of the tool. The cutting tool must be kept sharp, which will ensure efficient and safe functioning.
Follow the guidelines regarding installation of accessories and lubrication. It is required to revise periodically the power supply
cord, and in case any defects are detected, before work it is required to have the power supply cord replaced in an authorised
service point of the manufacturer. It is required to periodically revise the extension cord, and damaged extension cords must be
replaced with new ones.
The handles must be maintained dry, clean and free from lubricants and oils.
Disconnection of the tool. If the tool is not used, then before any service tasks and replacement of accessories, such as blades,
drills and cutters, it is required to disconnect the tool from the power supply source.
Remove the keys used for adjustments. It is required to have the custom to make sure the keys used for adjustments have been
removed before the tool is started.
Avoid accidental activation of the tool. Make sure the switch in ON, before the tool is connected to the power supply source.
Using external extension cords. If the tool is used outdoors, then to power it is required to use extension cords for outdoor use.
Be alert. Watch what you are doing. Use common sense and do not work when you are tired.
Checking for damaged parts. Before you continue to use the tool, it is required to revise it thoroughly and make sure it will be
functioning properly, performing its intended functions.
Check the matching of the mobile parts, seizures of mobile parts, check for broken parts, check installation and other conditions,
which may influence the operation of the tool. The guards and other damaged parts must be properly repaired or replaced in an
authorised service point of the manufacturer, unless otherwise indicated in the manual. Damaged switches must be replaced in an
authorised service point of the manufacturer. Do not use the tool, if the switch does not turn it on or off.
Attention! Using accessories other than those recommended in the manual may increase the risk of injuries.
Have the tool repaired by qualified personnel. The tool complies with important safety requirements. Repairs should be realised by
qualified personnel, using original spare parts. Otherwise, repairs may lead to significant dangers for the user.
ADDITIONAL SAFETY GUIDELINES
Do not use damaged or deformed circular saws.
A worn table insert must be replaced with a new one.
Use only circular saws of parameters indicated in the technical data table. Circular saws designed for wood should comply with
the requirements indicated in the standard EN 847-1.
Do not use circular saws made of high speed steel (HSS).
Use individual protection means each time it is necessary. Wearing hearing protection decreases the risk of hearing loss. Sight
protection. Respiratory system protection means reduce the risk of inhalation of harmful dust. Gloves to handle circular saws and
coarse materials. Circular saws should be carried by the handles.
Connect dust extraction system in case of cutting wood.
Select a circular saw designed for cutting of the given material.
Attention! Do not cut materials other than those indicated in the manual.
The tool must be lifted and carried holding it by the working table. Place the hands away from the edges of the circular saw. Before
lifting or carrying the tool, make sure all the mobile parts have been locked. Do not use the guards to lift or transport of the tool.
Use the tool only with guards which are in good conditions, properly maintained and correctly installed.
The floor at the work area must be maintained clean.
Make sure the speed indicated on the disc is higher or equal to the speed indicated on the tool.
In case of using spacer rings or other spindle rings, make sure the manufacturer permits to use them for the task in question.
If the tool is equipped with a laser indicator or a LED indicator, then they must not be replaced with devices of another type than
those installed. All repairs or replacements should be realised in an authorised service point of the manufacturer.
Attention! Refrain from removing cut elements or other parts of the material from the cutting area, while the tool is working and
the circular saw is uncovered.
Make sure cutting is correct and safe. Always fix the material to be cut to the working table. Before work may start, make sure the
tool is stable. If required, fox the tool to the table. In case it is necessary, support the material to be cut, if it is long.
O R I G I N A L I N S T R U C T I O N S
14