Hozelock Cyprio EasyClear 6000 Manual De Instrucciones página 6

to always bypass in to the pond even if the fountain
head becomes blocked ensuring clear water. If the
pond water is not clearing sufficiently it may be
necessary to allow more water to bypass in to the
pond by opening the waterfall outlet.
The 2 and 3 tier fountainheads simply snap onto the
fountain stem. The fountain angle can be adjusted to
be vertical using the ball joint (Fig 2-L). The tightness
of the ball joint can be adjusted (Fig 2-M) if required,
the 2- Tier Fountainhead can be used to achieve an
alternative and higher display pattern than the 3-Tier.
The fountain height can be adjusted to suit your needs
by rotating the Fountain Flow Adjuster (Fig 3B-N). Turn
the Waterfall Adjuster (Fig 3A-O) until closed to obtain
the maximum fountain height.
The Bell Fountain creates a decorative 'water bell'. The
size of the bell can be adjusted to suit your needs by
rotating the Fountain Flow Adjuster (Fig 3B-N).
Install and position the pump as previously described
and switch on.
Fountain and Waterfall Operation
Attach a suitable length (3m maximum) of 25 mm (1")
hose to the hose tail on the Waterfall Adjuster (Fig 3A-
Q) and secure with a suitable hose clip and position
the outlet end of the hose in the desired position.
Screw the Waterfall Adjuster onto the waterfall outlet
on the front of the EasyClear™ (Fig 3A-Q).
Once the pump is operating the flow of the waterfall
and the height of the fountain can be independently
adjusted using the Fountain Adjuster (Fig 3B-N) and
Waterfall Adjuster (Fig 3A-O).
Install and position the pump as previously described
and switch on.
Waterfall Only Operation
(Fig 4 for general installation guide)
Screw the blanking plug onto the fountain outlet (Fig
3A-P).
Attach a suitable length (3m maximum) of 25 mm (1")
hose to the hose tail on the Waterfall Adjuster (Fig
3A-O) and secure with a suitable hose clip and position
the outlet end of the hose in the desired position.
Screw the Waterfall Adjuster onto the waterfall outlet
on the front of the EasyClear™ (Fig 3A-Q).
Adjust the flow using the Waterfall Adjuster, (Fig 3A-
O), to suit your needs.
Install and position the pump as previously described
and switch on.
UVC Operation
The UVC will automatically switch on once the unit
has been connected to the electricity supply if the
bayonet tube is correctly locked in place.
The UVC lamp can be checked for operation by
looking for a bluish glow from ball joint outlet (Fig
1-A). Please note that this may only become visible in
low light conditions.
See Maintenance section for Lamp replacement.
Maintenance
The Hozelock Cyprio EasyClear™ has been designed
to allow fast and easy maintenance. As with all pond
equipment, occasionally it will become necessary to
clean or replace parts.
WARNING: Disconnect this product from the
electricity supply and refer to the section "Safety
& Electrical Connections" before attempting any
maintenance.
Fountain Head (Fig 1-E)
Follow the below procedure if the fountain head is
blocked:
1 - Place a coin or similar in the slot and gently lever
off the fountain head.
2 - Rinse in clean water and reassemble.
Foam
Follow the below procedure if flow appears reduced:
1 - Release the Foam Cover by pushing the two
buttons (Fig 5-R) and lift the cover (Fig 6-S).
2 - Remove the Foam (Fig 7-T). Note:- If the unit is
out of the pond for more then 20 minutes the
biological filter action may stop working. Rinse
thoroughly in pond water (do not use tap water).
3 - The Foam Cover and Base should also be rinsed in
pond water (do not use tap water).
4 – It may also be necessary to clean out the
biomedia and stones (Fig 7-U) if these have
become clogged. If this is necessary, the biomedia
and stones should be rinsed in pond water only.
5 - Reassemble the Filter.
Quartz Tube
Follow the below procedure if your pond remains
green:
1 - Remove the bayonet locking screw (Fig 8-V), twist
and lift the bayonet tube (Fig 8-W).
2 - Clean the Quartz Tube. Take extra care when
handling the Quartz tube. In hard water areas,
the quartz tube may become covered in limescale,
which will reduce efficiency. Clean the tube with a
soft cloth and a gentle de-scaler (such as vinegar
and water), rinse in water before refitting.
3 - Reassemble the bayonet tube and screw and
restart (Fig 8-X).
Warning! Ensure that the quartz tube is not
damaged before refitting.