General Features; Main Components; Technical Features; Compliance With Standards - Anest Iwata Stainless Steel PET-10N Manual De Instrucciones De Uso

EN PET Series | Stainless Steel Pressure Tanks

2.1 GENERAL FEATURES

THE TECHNICAL FEATURES OF THE VARIOUS MODELS ARE LISTED
IN PARAGRAPH 2.3.
The tank is composed of two main parts: the body and the lid.
The equipment described in this manual is a Stainless Steel
Pressure Tank PET model for paint spraying systems. The pressure
inside the tank allows spraying the paint with a pressure between 0
and 7 bar (700 kpa). The possibility to adjust the product pressure
improves the quality of application and facilitates the flow of highly
viscous products.
The body of the tank is provided with six fixing clamps (four in the
10lt version), guaranteeing the perfect tightness of the system, and
with two lifting handles to facilitate handling the whole unit.
The following items are located on the closure lid:
- The air inlet connection and its ball valve (L);
- The fluid outlet connection and its ball valve (D);
- An air pressure regulator provided with pressure gauge for
checking the inner pressure (P and M);
- A safety valve (Q) and an exhaust valve to drain pressure (N);
- An handle for opening up (F);
A set of packings located on the contact areas of the components
guarantee a perfect pressure tightness.
Models PET-10/30/50 MN are equipped with a pneumatic agita-
tor (G) provided with a practical mixing vanes speed controller
(H): this allows keeping the paint properly stirred and suspended,
therefore avoiding deposits and sedimentation.
To avoid damage due to static electricity, the whole group is provided
with ground connection.

2.3 TECHNICAL FEATURES

MODELS
Tank capacity:
Version with pneumatic agitator:
Weight:
Dimensions (HxW):
Max. operating air pressure:
Max. fluid pressure:
Max. air inlet pressure:
Operating supply pressure:
Air inlet joint:
Fluid outlet joint:
Paint filter:
Operating temperature:
Fluid passages:

2.4 COMPLIANCE WITH STANDARDS

Several safety systems have been arranged during the design and manufacturing of Pressure Tanks PET series, in order to protect the
safety of the user, in compliance with:
Directive 2014/34/EU
Directive 2006/42/EC
Directive 2014/68/EU
4
(The table below provides the technical features of the models described).
PET-10 PET-30
N MN N
10 lt. 30 lt.
- AM-6B -
15,3 Kg 17,5 Kg 20,4 Kg
540x330 mm 710x415 mm
7 bar (0.7 MPa)
7 bar (0.7 MPa)
7 bar (0.7 MPa)
from 0 to 7 bar
G 1/4" M
G 3/8" M
40 Mesh /ø 51 mm
5~40 °C
AISI 303, AISI 304
PET-10 N - PET-10 MN (10 lt.)
PET-30 N - PET-30 MN (30 lt.)
0035
I 2 G c IIB T5 Gb
ATEX group I - category 2G - constructional safety -
all gases IIA and IIB - class T5 - high protection level

2.2 MAIN COMPONENTS

Body of the tank
A
Tank lifting handle
B
Lid
C
Fluid outlet connection
D
Fluid outlet ball valve
E
Lid lifting handle
F
Pneumatic air motor
G
Agitator speed controller
H
G
I
H
L
E
D
Q
P
M
PET-50
MN N MN
50 lt.
AM-6B - AM-6B
22,6 Kg 25,6 Kg 28,2 Kg Air consumption:
810x470 mm
40 Mesh /ø 78 mm
PET-50 N - PET-50 MN (50 lt.)
ATEX group II - category 2G - constructional safety -
all gases IIA and IIB - class T5 - high protection level
Air inlet ball valve
I
Air inlet connection
L
Air pressure regulator
M
Exhaust Valve
N
Clamp
O
Pressure gauge
P
Safety valve (7 bar)
Q
F
C
O
N
PNEUMATIC AGITATOR
AM-6B
Max. operating pressure:
Speed: 500 rpm
15 l/min
Max. air inlet pressure:
Supply air filtration:
Air motor lubrication: 2-3 ml/500H
Noise level: 65 dB(A)
0035
II 2 G c IIB T5 Gb
B
A
1~5 bar
7 bar
50 μm