Electrical Safety - Ferm OTM1005 Traducción Del Manual Original

Tabla de contenido

Publicidad

after mounting the accessories. If the machine
vibrates strongly, immediately switch off the
machine, remove the mains plug from the
mains, and try to solve the problem.
• Make sure that the workpiece is properly
supported or fixed.
• Wear safety goggles. Wear hearing protection.
Wear a dust mask. If necessary, use other
protective means, such as safety gloves,
safety shoes, etc. Risk of personal injury.
• Keep bystanders away from the work area.
Make sure that all persons in the work area wear
protective equipment. Risk of personal injury.
• Keep the mains cable away from the rotating
accessory. If the mains cable touches the
rotating accessory, your hands or arms may
come in contact with the accessory. Risk of
personal injury.
• Hold the machine by the insulated gripping
surfaces where the accessory may contact
hidden wiring or the mains cable. If the
accessory contacts a 'live' wire, the exposed
metal parts of the machine can also become
'live'. Risk of electric shock.
• Do not use the machine while carrying it at
your side. Risk of personal injury.
• Do not use the machine near flammable
materials. Risk of fire.
• Beware that the accessory continues to
rotate for a short period after switching off
the machine. Do not attempt to bring the
accessory to a standstill yourself.
• Never put the machine down on a table or a
workbench before it has been switched off.
• Regularly clean the ventilation slots. Risk of
electric shock.

Electrical safety

Always check that the voltage of the
power supply corresponds to the voltage
on the rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
• Only use extension cables that are suitable for
the power rating of the machine with a minimum
thickness of 1.5 mm
. If you use a extension
2
cable reel, always fully unroll the cable.
Mains plug replacement (UK only)
If the moulded 3-pin plug attached to the unit is
damaged and needs replacing, it is important
that it is correctly destroyed and replaced by an
approved BS 1363/3A fused plug and that the
following wiring instructions are followed.
The wires in the mains cable are coloured in
accordance with the following code:
blue
neutral
brown
live
As the colours of the wires in the mains cable
of the unit may not correspond to the coloured
markings identifying the terminals in the plug,
proceed as follows:
- The wire which is coloured blue must be
connected to the terminal which is marked
with the letter N or coloured black.
- The wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red.
Technical data
Mains voltage
Mains frequency
Power input
No-load speed
Weight
Noise and vibration
Sound pressure (Lpa)
Acoustic power (Lwa)
Uncertainty (K)
Vibration (sanding on wood)
Vibration (sawing in wood)
Vibration (scraping in wood)
Vibration (sawing in steel)
Uncertainty (K)
Wear hearing protection.
Vibration level
The vibration emission level stated in this instruction
manual has been measured in accordance with
a standardised test given in EN 60745; it may be
used to compare one tool with another and as a
preliminary assessment of exposure to vibration
when using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories,
OTM1005
V~
230
Hz
50
W
280
min-1
11,000 - 20,000
kg
1.5
OTM1005
dB(A)
85
dB(A)
96
dB(A)
3
m/s
4.2
2
m/s
7.3
2
m/s
8.1
2
m/s
5,6
2
m/s
1.5
2
5

Publicidad

Tabla de contenido
loading

Tabla de contenido