Behringer POLY D Guia De Inicio Rapido página 55

RECALLING A SAVED PATTERN
1. Press and hold PATTERN. The LOCATION LED
will show the current pattern number. Use the
<KYBD or STEP> switches to move up and
down through the patterns 1 to 8, or press a
STEP switch 1 to 8. You can also do this while a
pattern is playing.
2. Press and hold SHIFT and PATTERN. The
LOCATION LED will show the current bank
number. Use the <KYBD or STEP> switches to
move up and down through the banks 1 to 8,
or press a STEP switch 1 to 8. You can also do
this while a pattern is playing.
3. Press PLAY/STOP to play back the
current pattern.
4. During playback, the LOCATION LEDs will show
the current page of the pattern (1 to 4), and the
STEP Switch LEDs will show the steps moving.
LIVE PERFORMANCE
During playback, temporary adjustments can be
made as follows. (None of these are saved with
the pattern.)
1. To add Ratchet to all steps of the pattern, press
SHIFT and adjust the GLIDE control.
2. To add SWING, press SHIFT and adjust the
TEMPO control.
3. To mute the pattern, press SHIFT + HOLD/REST.
4. To add an accent to all steps, press SHIFT +
RESET/ACCENT.
EDITING A PATTERN
1. To edit a pattern in Keyboard mode, press REC.
The STEP switch LEDs will light.
2. Press PAGE to select the pattern page from 1 to
4 to be edited. The green LOCATION LEDs 1 to 4
will show the current page.
3. Press SHIFT and the STEP switch you want to
edit. You can enter a new note, or a rest, and
adjust any of the other parameters such as
ratchet, glide on/off, and so on.
4. Press SHIFT and the next STEP switch to be
edited. (The steps will not automatically
advance to the next step in line; you can choose
which steps to edit next.)
5. Press REC to exit the editing mode.
6. Press PLAY/STOP to listen to the edited pattern.
7. Remember to save the pattern using the
"SAVING A PATTERN" procedure above.
CREATING A PATTERN IN STEP MODE
1. Press SHIFT and STEP> to select the Sequencer's
STEP mode. The flashing LOCATION LED will
turn from green (Keyboard mode) to yellow
(Step mode).
2. Initialise the current pattern by pressing SHIFT,
RESET, and PATTERN at the same time. This will
delete any previous steps of the current pattern.
(If you want to use the current pattern instead,
then do not initialise it.)
3. Press PAGE to move to a desired page of
your pattern. Then press SET END and a STEP
switch to choose the length of the pattern. For
example, if you are on page 1 and press SET
END + 8, then the pattern length is 8 steps.
If you press PAGE and reach page 4, and press
SET END + 8, then the pattern will be 32 steps
long (4 pages of 8 steps each).
4. When the desired SET END is selected, all the
STEP switch LEDs up to that step will be on
solid red.
5. Press SHIFT and any one of the STEP switches at
the same time. It will begin to flash, indicating
it is the current step about to be edited. You can
now add a note, or a rest, or any of the other
functions described above in the Keyboard
mode, such as Ratchet, Glide, Accent, change
gate length and so on.
6. Press SHIFT and the current STEP switch to finish
editing that step. It will stop flashing.
7. Repeat procedure steps 5 and 6 above, until all
your required steps are good.
8. Press PLAY/STOP to play the pattern.
9. While playing, you can add temporary
adjustments as shown in the "LIVE
PERFORMANCE" procedure above.
SAVING A PATTERN IN STEP MODE
1. Patterns created in STEP mode are not saved in
this mode.
2. If you wanted to save it, first switch back to
KEYBOARD mode by pressing SHIFT + <KYBD.
3. Caution: Do not turn off the unit, or create a
new pattern, or the current unsaved pattern
will be lost.
4. Save the pattern using the "SAVING A
PATTERN" procedure shown above for the
KEYBOARD mode.
55
Quick Start Guide