Black and Decker GWC3600L Manual De Instrucciones página 7

If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. Blow tube
2. Vac tube
3. Collection bag
4. Blow/Vac
5. On/Off switch
6. Power select
7. Battery
8. Feet
Assembly
@
Warning! Before assembly, make sure that
the appliance is switched off and the battery is
removed.
@
Warning! Always wear protective gloves when
working with your cordless sweeper.
Blow tube assembly (fig. A)
The blow tube (1) must be assembled before use.
Align the latches (9) on the side of the blow tubes (1).
u
Push the blow tube (1) firmly into each other until the
u
latches (9) click into place.
Note! The tubes should not be separated once assembled.
Note! The concentrator can be removed from the end of the
blow tube by firmly pressing the catch (22) and pulling.
Vac tube assembly (fig. B)
The vac tube (2) must be assembled before use.
Align the latches (10) on the side of the vac tube (2).
u
Push the vac tube (2) firmly into each other until the
u
latches (10) click into place.
Note! The tubes should not be separated once assembled.
Fitting and removing the battery (fig. C)
To fit the battery (7), line it up with the receptacle on the
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (11) while
u
at the same time pulling the battery out of the receptacle.
Attaching the second handle (fig. E)
Press in and hold both of the buttons (20) on the side of
u
the handle.
Slide the second handle (21) in place over the buttons
u
(20).
(Original instructions)
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Adjusting the position of the second handle
The second handle (21) can be adjusted to provide optimum
balance and comfort.
Press in the button (20) on the left side od the handle.
u
Rotate the second handle (21) into the required position.
u
Release the button (20).
u
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. D)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
To charge the battery (7), insert it into the charger (12).
u
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
u
The charging indicator (13) will flash green continuously
(slowly).
The charge is complete when the charging indicator (13)
lights green continuously. The charger and the battery can be
left connected indefinitely with the LED illuminated. The LED
will change to flashing green (charging) state as the charger
occasionally tops off the battery charge. The charging indica-
tor (13) will be lit as long as the battery is connected to the
plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
ENGLISH
7