Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
CABLE
75
CABLE
HDMI 1
HDMI 2
TV
OUTPUT
IN
3
Set-Top Box
CABLE / ANTENNA
HDMI 2
HDMI 1
T
AV1 :
L + R + VIDEO
4
2
3
OUT
IN
Set-Top Box
Watching Cable TV programs that don't
require the cable box
Since you've connected the cable TV signal
directly to the TV's tuner, you can also watch the
unscrambled programs by simply tuning to the
desired channel. You must first use Autoprogram,
however, to store channels in the TV's memory.
Note: This connection will supply stereo sound to
the TV if it is being broadcast by the station you are
watching.
&
Basic connections to the TV
Your integrated digital TV automatically decodes and displays the four basic DTV
picture resolution standards.
- SDTV (Standard Definition TV) are broadcast as 480i (480-line interlaced) or
480p (480-line progressive scan) video.
- HDTV (High-Definition TV) are broadcast either in the 1080i or 720p formats,
always with a widescreen picture.
Note: Progressive scan video (p) is more like that you see in a movie theater. Images are
much more distinct and free of flicker, and motion is smoother.
Next to analog NTSC broadcast reception, your TV has an integrated High
Definition TV tuner which receives, decodes and displays terrestrial ATSC and
unscrambled cable (QAM) signals.
HDTV quality is only reproduced when a broadcaster or cable provider broadcasts
HDTV signals.
There are 2 ways to get HDTV content:
- via cable,
- via antenna.
Note: This drawing is used wherever you can connect cable or antenna.
Back of the TV
- Cable TV
75
Connect the cable TV signal to the
of the TV.
Note: this connection will supply stereo sound to the TV if it is being broadcast by the
station you are watching.
2
- Cable box with
• Connect the incoming cable TV signal to the cable
the cable box.
• Connect a coaxial cable (not supplied) from the
cable box to the
Note: Your cable box may have a different label for the
OUTPUT
• Set the
correct for your cable box), then tune the TV to the corresponding channel.
Once tuned, change channels at the cable box, not the TV.
Note: This connection will not supply stereo sound to the TV. The reason is that the RF
output on a cable box - labeled
CABLE
stereo signal to the tuner (VHF/UHF) input on a TV.
1
- Cable box with A/V outputs
• Connect the incoming cable TV signal
SIGNAL
SPLITTER
signal splitter enables you to avoid having to use the TO TV jack on the back of
the cable box. This jack will not supply stereo sound to the TV.
Note: Your cable box may have a different label for the
OUTPUT
• Connect a coaxial cable (not supplied) to a connector on the signal splitter and
to the
• Connect another coaxial cable (not supplied) to a connector on the signal
splitter and to the cable
• Connect A/V cables (not supplied) to the
on the back of the cable box and to the
AUDIO
• To view programs from your cable box, first press the
remote control.
• Press the cursor down or up buttons until the
• Press the
becomes current for the viewing of cable TV programs through your cable box.
Note: If your cable box Audio/Video outputs will not supply video and stereo audio to
the TV, you will need to make the connection shown above in the example "Cable box
with
CABLE/ANTENNA 75 Ω :
RF IN/OUT
CABLE/ANTENNA 75 Ω :
or
.
OUT
switch
3
of the cable box to
OUTPUT CH
,
TO TV
OUT
or
.
OUT
CABLE/ANTENNA 75 Ω :
jack
jack
3
on the back of the cable box.
IN
4
(labeled
and
) jacks
on the back of the TV.
L
R
button to confirm your selection. The
OK
".
RF IN/OUT
3
jack at the bottom
jack
1
on the back of
IN
jack on the back of the
TO TV
2
jack
at the bottom of the TV.
jack, such as
TO TV
or
(whichever is
CH 3
4
or
for example - will not send a
OUTPUT
1
to a signal splitter (not supplied). The
jack, such as
TO TV
2
on the TV.
and
and
VIDEO
AUDIO L
R
video (labeled
) and
AV2
VIDEO
button on the
SOURCE
signal source is selected.
AV2
input source
AV2
outputs
Publicidad
Capítulos
Tabla de contenido
