Fontanot nice Serie Manual De Instrucciones página 6

2) Heat for about five minutes making circular movements without stopping and make sure that the flame does
not come into direct contact with the handrail
3) Turn over the handrail and repeat the operation (Fig. 13).
It is advisable to wear protective fabric gloves during this operation.
25. B efore it cools down, position the handrail A02 on the balusters CB6 starting from the top of the staircase (Fig. 14).
26. U sing a 5mm Ø bit, drill the handrail A02 in correspondence to the holes in the end part B53 of the pole CB6.
Secure the handrail A02 using elements B54 and B55 (Fig. 14).
27. Cut the excess handrail A02 in correspondence to the first baluster CB6 of the staircase.
28. Complete the handrail A02 by fixing the parts A03 using glue X01 (Fig. 1).
29. J oin the end part of the railing to the section of the balustrade on the landing E04 using the appropriate fixture
obtained by assembling the parts A20, A03, C92 and B08 (Fig. 15).
30. J oin the fixture obtained to the handrail A02 using the screws C87 after drilling the holes underneath the
handrail using a 2.5mm Ø bit (Fig. 15).
31. I nsert the steel cables F30 into articles C69 found on the balusters CB6 (Fig. 16). Secure the cables on one of
the two ends with articles D37 and C76, leaving an extra 5mm of cable protruding from article D37 (Fig. 17).
Tighten the cables by hand at the opposite end and secure using articles D37 and C76. Cut the cables at a
distance of 5mm from article D37. Screw on the cable protection parts D36 (Fig. 16-17).
Warning: when cutting the cables, we recommend wrapping the part in question with adhesive tape in order to
avoid fraying, use a suitable shearer.
32. Complete railing assembly by fitting the parts B82 to the lower part of the balusters CB6 (Fig.1).
Assembling the balustrade
33. T o fasten the balusters CB7 of the balustrade, drill 4 equidistant holes in the landing E04 using a 5mm Ø bit.
Keep a distance of about 50mm from the edge and a distance of 25mm between the first hole and the part B05
(Fig. 18). Position elements F01 on landing E04 using elements C89 and B02 (Fig. 20).
34. Screw column C04 onto element G01 protruding from the landing E04 (Fig. 20).
35. P osition the balusters CB7 (H. 935) in the parts F01 with the components C69 facing the outside and tighten
the parts B02 (Fig. 20).
36. Fit the part B01 to the column C04 and secure it using the part B02 (Fig. 20).
37. U sing a 5mm Ø bit, drill the handrail A18 in correspondence to the holes in the end part B53 of the poles CB7
and in the part B01. Secure the handrail A18 using elements B54 and B55 (fig. 20).
38. D epending on the position and whether there are walls around the opening of the staircase, one or two extra
balusters CB7 may need to be positioned. In this case, allow for a space equidistant from the other balusters or
from the wall. To secure these, we recommend drilling the landing with a Ø 10mm bit and using elements F01,
C84, B27, B23, C31 (fig. 19).
39. Complete the handrail A18 by fixing the parts A03 using glue X01 (Fig. 20).
40. I nsert the steel cables F30 into articles C69 found on the balusters CB7. Secure the cables on one of the two
ends with articles D37 and C76, leaving an extra 5mm of cable protruding from article D37 (Fig. 20). Tighten the
cables by hand at the opposite end and secure using articles D37 and C76. Cut the cables at a distance of 5
mm from article D37. Screw on the cable protection parts D36 (Fig. 20).
Warning: when cutting the cables, we recommend wrapping the part in question with adhesive tape in order to
avoid fraying, use a suitable shearer.
Final assembly
41. T o further stiffen the staircase at intermediate points, fasten the parts F09 on the wall and join them to the
balusters CB6 using the parts F08. Drill using an 8 mm Ø bit and use the parts B85, B86, C90, B12 (Fig. 21).
7 - NICE LINE