Dyson SV10 Manual De Instrucciones página 12

USING YOUR DYSON MACHINE
PLEASE READ THE "IMPORTANT SAFETY INSTRUCTIONS" IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
OPERATION
• Do not use outdoors or on wet surfaces or to vacuum water or other liquids – electric
shock could occur.
• Ensure the machine remains upright in use. Dirt and debris may be released if it is
turned upside down.
• Do not operate while checking for blockages as doing so could result in
personal injury.
• For domestic indoor and car use only. Do not use it while the car is in motion or
while driving.
• To operate the MAX mode, locate the switch on the top of the machine. Slide the
switch to the Max mode position.
• To switch off MAX mode, slide the red switch back to the Powerful Suction
mode position.
• This machine has carbon fiber brushes. Take care if coming into contact with them,
as they may cause minor skin irritation. Wash your hands after handling the brushes.
DIAGNOSTICS – LIGHTS DURING CHARGING
Charging from low.
Charging, medium charge.
Charging, nearly full.
Fully charged.
Battery fault – call the Dyson Helpline
Charger fault – call the Dyson Helpline.
DIAGNOSTICS – DURING USE
High level of charge.
Medium level of charge.
Low level of charge.
Empty – please recharge.
Battery fault – call the Dyson Helpline
Main body fault – call the Dyson Helpline.
DOCKING STATION INSTALLATION
• Use appropriate mounting hardware for your wall type and ensure that the docking
station is mounted securely. Ensure no pipe work (gas, water, air) or electrical cables,
wires or ductwork are located directly behind the mounting area. The docking station
must be mounted in accordance with regulations and applicable codes/standards
(state and local laws may apply). Dyson recommends the use of protective clothing,
eyeware and materials when installing the docking station.
CARPETS OR HARD FLOORS
• Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
• The brush bar on the machine can damage certain carpet types and floors. Some
carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, we
recommend vacuuming without the motorized floor tool and consulting with your
flooring manufacturer.
• Before vacuuming highly polished floors, such as wood or linoleum, first check that
the underside of the floor tool and its brushes are free from foreign objects that could
cause marking.
12
LOOKING AFTER YOUR DYSON MACHINE
• Do not carry out any maintenance or repair work other than that shown and
described in this Dyson Operating Manual.
• Only use parts recommended by Dyson. If you do not this may invalidate
your warranty.
• Store the machine indoors. Do not use or store it below 37.4°F (3°C). Ensure the
machine is at room temperature before operating.
• Clean the machine only with a dry cloth. Do not use any lubricants, cleaning agents,
polishes or air fresheners on any part of the machine.
VACUUMING
• Do not use without the clear bin and filters in place.
• Fine dirt such as plaster dust or flour should only be vacuumed in very small amounts.
• Do not use the machine to pick up sharp hard objects, small toys, pins, paper clips,
etc. They may damage the machine.
• When vacuuming, certain carpets may generate small static charges in the clear
bin or wand. These are harmless and are not associated with the central electricity
supply. To minimize any effect from this, do not put your hand or insert any object into
the clear bin unless you have first emptied it. Clean the clear bin with a damp cloth
only. (See "Cleaning the clear bin".)
• Use extra care when cleaning on stairs.
• Do not rest the machine on chairs, tables, etc.
• Do not press down on the nozzle with excessive force when using the machine as this
may cause damage.
• Do not leave the cleaner head in one place on delicate floors.
• On waxed floors the movement of the cleaner head may create an uneven luster. If
this happens, wipe with a damp cloth, polish the area with wax, and wait for it to dry.
EMPTYING THE CLEAR BIN
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Ensure the machine is disconnected from the charger before emptying the clear bin.
Be careful not to pull the "ON" trigger.
• To make emptying the clear bin easier, it is advisable to remove the wand and
floor tool.
• To minimize dust/allergen contact when emptying, encase the clear bin tightly in a
plastic bag and empty.
• To release the dirt, hold the machine by the handle, pull the red lever back and lift
upwards to release the cyclone. Continue until the bin base automatically opens and
releases the dirt.
• Remove the clear bin carefully from the bag.
• Seal the bag tightly, dispose as normal.
• To close, push the cyclone downwards until it is in the normal position and manually
close the base of the bin – the base will click when it is securely in place.
CLEANING THE CLEAR BIN
• Ensure the machine is disconnected from the charger before removing the clear bin.
Be careful not to pull the "ON" trigger.
• Remove the wand and floor tool.
• To remove the cyclone, hold the machine by the handle, pull the red lever towards
you and lift upwards until the bin opens, then push in the red button located behind
the cyclone and lift the cyclone out.
• To detach the clear bin from the machine, pull back on the red catch located at the
base, slide the clear bin down and carefully remove forwards from the main body.
• Clean the clear bin with a damp cloth only.
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the clear bin in a dishwasher.
• Ensure the clear bin is completely dry before replacing.
• To replace the clear bin, align the tabs on the clear bin with the grooves on the main
body and slide upwards into place until the catch clicks.
• Slide the cyclone into the grooves of the main body and push downwards until it is in
its normal position and manually close the base of the bin – the base will click when it
is securely in place.
WASHABLE PARTS
Your machine has washable parts, which require regular cleaning. Follow the
instructions below.
WASHING THE BRUSH BAR
• Your appliance has a washable brush bar, check and wash it regularly according to
the following instructions to maintain performance.
• Ensure the machine is disconnected from the charger before removing the brush bar.
Be careful not to pull the 'ON' trigger.
TO REMOVE, WASH AND REPLACE THE BRUSH BAR:
• Please refer to the 'Washing the brush bar' illustrations alongside the
instructions below.
• Turn the cleaner head upside down so the underside of the cleaner head is
facing you. Use a coin to turn the fastener one quarter counter-clockwise to the
unlocked position.
• Rotate the end cap to the open position. Gently slide the brush bar away from the
cleaner head.
• Remove the end cap from the brush bar.
• Hold the brush bar under running water and gently rub to remove any lint or dirt.
• Stand the brush bar upright as shown. Leave to dry completely for a minimum of
24 hours.
• Before replacing, check that the brush bar is completely dry.
• Reattach the end cap to the brush bar.
• Slide the brush bar back onto the cleaner head, around the motor. The end cap
should be in the open position as shown. Once in place, rotate the end cap back into
the closed position.
• Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is fully
turned and the brush bar is secure.