To Clear A Macro; Problems And Troubleshooting - Emtec H340 Guia Del Usuario

f. "Please Wait" will be displayed briefly and the remote will exit Setup routine and return to normal
operation
9. Macros
The MACRO key, in conjunction with digits 1, 2 and 3, lets you to program and store up to 3 sequences of
key-presses of your choice. One press of the respective Macro digit key results in that sequence of key-
presses (IR commands) being sent. Any sequence of key-presses that you regularly perform can be
reduced to two keypresses (MACRO key followed by digit 1, 2 or 3 key). For example pressing MACRO
followed by a single key can turn on your TV, turn on your cable box, change to your favourite channel, turn
on your VCR, and tell it to record, etc. A total of 10 keypresses can be stored under each of the 3 Macro
digits.
9.1 To Setup a Macro
a. Press and hold S key until "Code Setup" is displayed (takes approximately 3 seconds).
b. Release S key.
c. Using the Up/Down keys, navigate to "Macro Setup". Press and release OK key.
d. "Macro Key Set" is displayed. Press and release OK key.
e. "Select a Macro Key" is displayed. Press and release digit key 1, 2 or 3 where you want to store
the Macro.
f. "Select Macro X Mode" (where "X" is 1, 2 or 3) is displayed. Press and release the desired
Mode key (TV, VCR, DVD, etc.). The first key in a Macro sequence must always be a Mode key.
g. "Select Macro X Key?" is displayed along with the key count (initially "02"). Press and release
the keys you want to be included in the Macro, in the order you want them to be sent (up to
"10").
h. To store the Macro at any point, press and release the Macro key. Note the Macro will be stored
automatically on the 10th keypress.
i. "Success" will be displayed and the remote will exit Setup routine and return to normal
operation.

9.2 To Clear a Macro

a. Press and hold S key until "Code Setup" is displayed (takes approximately 2-3 seconds).
b. Release S key.
c. Using the Up/Down keys, navigate to "Macro Setup". Press and release OK key.
d. Using the Up/Down keys, navigate to the "Macro Key Clear" screen. Press and release OK
key.
e. "Select a Macro Key" is displayed. Press and release digit key 1, 2 or 3 for the Macro you want
to delete.
f. "Confirm OK to Clear" is displayed. Press and release OK key.
g. "Success" will be displayed briefly and the remote will exit Setup routine and return to normal
operation.
In normal operation, to activate the Macro press and release the MACRO key
followed (within 20 seconds) by the digit key 1, 2 or 3.
"Macro X" is displayed while the Macro sequence is being carried out then remote
returns to normal operation.
If no Macro is stored under the chosen digit key then "Macro X Void" is briefly
displayed and the remote returns to normal operation.
9.3 Macro Notes
1.You might want to add "delays" in a Macro sequence (e.g. to allow for your TV warm-up time). Delays
can be added by using the PAUSE key followed by the number of seconds delay required at Step "g" in
setting a Macro. For example, to enter a delay of 3 seconds, press and release
PAUSE followed by 3. Maximum delay is 9 seconds. It is not possible to have a
"0" digit entered after Pause i.e. there is no zero delay.
2. There is an automatic delay of half a second between each IR transmission
in a Macro sequence.
3. The first key stored in a Macro sequence MUST be a Mode key (TV, VCR, etc.).
4. Setup and Macro keys cannot be included in a Macro.
5. Press Setup to quit Macro Setup.

10. Problems and troubleshooting

The remote doesn't work or loses codes entered
X=1,2,3 X=1,2,3
- 22 -