Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Illustration 1
Screw
Pedestal
Illustration 2
Leveling glide
Left side
Leg
Leg locator
Illustration 3
Screw
Leg
Short leg
bracket
DESK AND RETURN
Screw
Outboard
panel
Top
Leg
Screw
Long leg
bracket
Left Side
Right Side
Leveling glide
Right side
Leg locator
Read all instructions and review illustrations
before installing.
Tools required for assembly:
/
" hex head screwdriver
1
4
Lifting a drawer using drawer follower or
hangrails can cause the drawer follower or
hangrails to come loose. The drawer can fall and
cause serious injury to you or others. Lift drawer
by a fixed part of the drawer.
Sharp edges may cause injury. Take care when
handling metal parts.
Preparing Desk for Leg Installation:
1. With drawers locked, use two or more people to
place desk upside down on cardboard or a carpet-
ed surface (this is to prevent the top from being
scratched).
2. Refer to Illustration 1. Locate leg bracket screws
attached to bottom of pedestal and outboard panel.
Use the straight blade or
to remove screws. Save screws for later use.
3. Remove legs from packing.
Attaching Legs to Desk Pedestal(s) (refer to
Illustration 2).
1. With leg slots facing center of desk, insert a leg over
a leg locator on the bottom corners of desk top.
2. Insert long leg brackets (from hardware pack) into
leg slots as shown in Illustration 1.
3. Align holes in leg bracket with holes in pedestal to
ensure leg is straight up and down. If leg is not
straight, remove leg bracket and insert it with
prongs facing the opposite direction (up or down).
/
4. Use the
" hex head screwdriver to reinstall
1
4
screws, removed in Preparing Desk for Leg
Installation: Step 2, securing leg bracket to
pedestal.
Attaching Legs to Outboard Panel (refer to
Illustration 3).
1. With leg slots facing center of desk, insert a leg over
a leg locator on the bottom corners of desk top.
2. Insert short leg brackets (from hardware pack) into
leg slots as shown in Illustration 1.
3. Align holes in leg bracket with holes in outboard
panel.
Leg
4. Use the
/
" hex head screwdriver to reinstall screws,
1
4
removed in Preparing Desk for Leg Installation:
Step 2, securing leg bracket to pedestal.
Completing Desk Installation:
1. Use two or more people to set desk upright.
2. Position desk where it will be used and adjust level-
ing glides to level desk front-to-back and side-to-
side.
Level
WARNING
/
" hex head screwdriver
1
4
SIDE 1 OF 3 (1/06)
42-2538M

Publicidad

loading

Resumen de contenidos para HON Mentor Serie

  • Página 1 DESK AND RETURN Illustration 1 Read all instructions and review illustrations before installing. Screw Screw Tools required for assembly: " hex head screwdriver Level Outboard Pedestal panel WARNING Lifting a drawer using drawer follower or hangrails can cause the drawer follower or hangrails to come loose.
  • Página 2 DESK AND RETURN Illustration 4 Wire Guide Frame Installation (refer to Illustration 4): Wire guide 1. Locate cut-outs on the pedestal(s) frame 2. Install a wire guide frame onto cut-out in interior wall (kneespace) of pedestal(s). Cut-out in interior wall of pedestal Illustration 5 Flush Return Installation: 1.
  • Página 3 DESK AND RETURN Illustration 7 Optional Drawer Pull Installation (refer to Illustration 7): Drawer front 1. Fully open drawers and locate holes in drawer fronts. 2. Align holes in rear of drawer pulls (from pull pack) with Drawer pull holes in drawer fronts. 3.
  • Página 4 BUREAU ET RETOUR Figure 1 Lisez toutes les instructions et examinez les figures avant d’entreprendre l’assemblage. Outils nécessaires à l’assemblage : Tournevis à tête hexagonale de Niveau Panneau Caisson extérieur ATTENTION On ne doit jamais soulever un tiroir au moyen d’une tringle ou d’une glissière, car une de ces pièces pourrait se détacher.
  • Página 5 BUREAU ET RETOUR Figure 4 Pour terminer l’installation du bureau : Guide-câbles 1. Remettez le bureau à l’endroit avec l’aide d’au moins une autre personne. 2. Placez le bureau à son emplacement final et ajustez les patins pour mettre le bureau de niveau dans le sens latéral, avant et arrière.
  • Página 6 BUREAU ET RETOUR Figure 7 Installation de poignée de tiroir [optionnel] (se reporter à l'illustration 7) : Devant de tiroir 1. Ouvrir complètement les tiroirs et repérer les trous dans l'avant de ceux-ci. Poignée de 2. Aligner les trous à l'arrière des poignées de tiroirs tiroir (dans la trousse de poignées) et ceux qui sont percés dans l'avant des tiroirs.
  • Página 7: Escritorio Y Extensión

    ESCRITORIO Y EXTENSIÓN Ilustración 1 Lea todas las instrucciones y revise las ilustra- ciones antes de realizar la instalación. Tornillo Tornillo Herramientas requeridas para el montaje: Destornillador de cabeza hexagonal de " Nivel Panel Pedestal exterior ADVERTENCIA Levantar un cajón usando los rieles de suspen- sión o contrabrida del mismo puede causar que dichas piezas se aflojen.
  • Página 8 ESCRITORIO Y EXTENSIÓN Ilustración 4 Terminar la instalación del escritorio: Marco guía 1. Con la ayuda de dos o más personas, enderece el escrito- para cable rio. 2. Coloque el escritorio en el lugar donde será utilizado y ajuste los niveladores a la misma la altura, de adelante hacia atrás y de un lado a otro.
  • Página 9 ESCRITORIO Y EXTENSIÓN Ilustración 7 Instalación del tirador de gaveta [opcional] (consulte la ilustración 7): Frente de la gaveta 1. Abra completamente las gavetas y ubique los agujeros en la parte frontal de las gavetas. Tirador de 2. Alinee los agujeros en la parte trasera de los tiradores (del gaveta paquete de tiradores) con los agujeros en la parte frontal de las gavetas.