Description Of The Hood - ELICA MERIDIANA EDS IX VT/A/120X70 Montaje Y Modo De Empleo

Fig. 7-8
5. Fit an exhaust pipe inside the truss and connect it to the
motor compartment connection ring (exhaust pipe and
fixing brackets are not supplied).
For filter versions (5F), fit deflector F to the truss and
secure it to the bracket supplied using 4 screws, then
connect the exhaust pipe to the connection ring located on
the deflector.
Fig. 9
6. Hook the frame onto the 4 screws (see step 4).
CAUTION! The side of the truss with connection box
corresponds to the side of the control panel with hood
assembled.
7. Tighten the 4 screws.
8. Insert and tighten another 2 screws in the remaining free
holes for secure fixing.
Note - only for the suction Version: connect the upper
end of the discharge tube to the discharge device toward
the exterior (e.g. hole in the ceiling).
9. Fix the reinforcement bracket (see operation 2) to the
lattice in as intermediate a position as possible.
Carry out the electrical connection to the mains power supply,
only turn on the power supply upon completion of assembly.
Fig. 10
10. Secure the hood to the truss using 8 screws.
CAUTION! The side of the truss with connection box
corresponds to the side of the control panel with hood
assembled.
Fig. 11
11. Connect the electricity of the command instrument panel
and the lamps.
Note: Place the excess cable on the apposite fairhead
(equipped with screw for tightening).
12. Join the two top sections of the flue to cover the truss so
that one of the slots on the sections is situated on the
same side of the control panel and the other on the
opposite side. Screw the two sections together with 8
screws (4 each side- see the plan diagram for joining the
two sections).
13. Fix the top flue assembly to the truss, near the ceiling,
with 2 screws (one each side).
Fig. 12
14. Couple the two lower sections of the flue to cover the
trellis using 6 screws (3 per side. See also the diagram
plan for coupling the two sections).
15. Insert the bottom section of the flue in its seat so that it
completely covers the motor compartment and electrical
connection box, then ensure it from inside the hood using
2 screws.
Fig. 13
16. Apply the 2 tabs (supplied) to cover the fixing points of the
bottom flue (CAUTION! THE BOTTOM FLUE TABS ARE
THE NARROWER AND SHALLOWER ONES).
The wider and deeper tabs are those used for the top flue,
and must be cut to size.
Turn the mains power on again at the central electrical panel
and check for correct hood operation.
Additional instructions for the montage
Installing the panel
(number and form of the panels can vary on the basis of the
model)
The panel is supplied dismounted.
Hook the panel onto the pins of the hood and fix with the
supplied latch S (the number varies on the basis of the model
- safety-fixing compulsory!).
Rotate the panels to cover the suction area and hook to the
pins, pressing with decision.
Check that the panel is blocked in position. Fig. 1

Description of the hood

Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour catcher
6. Telescopic chimney
7. Air outlet (used for filter version only)
8. Panel
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
To select the functions of the hood just touch the commands.
Light key ON/OFF
Intensive speed selection key (suction
power) - duration 5 minutes - press again to
return to previous setting.
High-speed selection key (suction power).
Medium-speed selection key (suction power)
- when flashing it indicates the need to wash or
replace the carbon filter. This signal is normally
deactivated.
14