English (Original Instructions) - DeWalt DCE530 Traducido De Las Instrucciones Originales

EngLIsH
HEAT GUN
DCE530
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
e
product development and innovation make D
most reliable partners for professional power tool users.
Technical Data
Voltage
Type
Battery type
Temperature at air outlet
Airflow
Weight (without battery pack)
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.

DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.

CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.

Denotes risk of electric shock.

Denotes risk of fire.
GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
Safety Instructions for Heat Guns
A fire may result if the appliance is not used with care, therefore:
• Heat may be conducted to combustible materials that
are out of sight. DO NOT use in a damp atmosphere,
24
WALT one of the
e
DCE530
V 18
DC
1
Li-Ion
°C 290 /530
l/min 109/190
kg 0.5
where flammable gases may be present or near
combustible materials.
• Place the appliance on its stand after use and allow it to cool
down before storage.
DO NOT leave the tool unattended while it is switched on.
•
DO NOT place your hand over the air vents or block the vents
•
in any way.
• The nozzle and accessories of this tool become extremely hot
during use. Let these parts cool down before touching.
ALWAYS switch the tool off before putting it down.
•
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Ensure adequate ventilation as toxic fumes may be produced.
DO NOT use as a hair dryer.
•
DO NOT obstruct either the air intake or nozzle outlet, as this
•
may cause excessive heat build up resulting in damage to
the tool.
DO NOT direct the hot air blast at other people.
•
DO NOT touch the metal nozzle as it becomes very hot during
•
use and remains hot for up to 30 minutes after use.
DO NOT place the nozzle against anything while using or
•
immediately after use.
DO NOT poke anything down the nozzle as it could give you
•
an electric shock. Do not look down the nozzle while the unit is
working because of the high temperatures being produced.
DO NOT allow paint to adhere to the nozzle or scraper as it
•
could ignite after some time.
DO NOT remove the heat barrel cover during use.
•
To reduce the risk of explosion, DO NOT use in paint spray
•
booths or within 3.0 m of paint spraying operations.
DO NOT use this tool to remove paint containing lead.
•
The peelings, residue and vapors of paint may contain lead
which is poisonous.
• Hidden areas such as behind walls, ceilings, floors, soffit
boards and other panels may contain flammable materials
that could be ignited by the heat gun when working in these
locations. The ignition of these materials may not be readily
apparent and could result in property damage and injury to
persons. When working in these locations, keep the heat gun
moving in a back-and-forth motion. Lingering or pausing in
one spot could ignite the panel or the material behind it.
NOTE: These heat guns are capable of producing
temperatures in excess of 530 ˚C.
DO NOT use this tool to heat food.
•
DO NOT lay the heat gun on flammable surfaces when
•
operating the gun or immediately after shutting it off. Allow
the tool to cool before storing. Always set the gun on a flat
level surface so that the nozzle tip is pointed upward.