SIOUX 1AM Serie Instrucciones

INSTRUCTIONS FOR NO. 1 SERIES "1AM" AIRCRAFT ANGLE DRILLS
Read and understand "Safety Instructions For Air Tools" and these instructions before
Tools left connected to the air supply while making adjustments, changing accessories, or doing any
Always remove tool from air supply and activate trigger to bleed air line before making any
adjustments, changing accessories, or doing any maintenance or service on tool.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pres-
sure regulator, and lubricator will insure maximum output and service life of tools.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 1/4" (6.35 mm) I.D. Extension hoses should be at least 3/8" (10 mm) I.D. Use couplings
and fittings with at least 1/4" (6.35 mm) I.D.
LUBRICATION
An airline lubricator, set to deliver one drop per minute, is recommended. If a lubricator is not used, add .04oz. (1.2 cc, 12 to
15 drops) of SIOUX No. 288 air motor oil into the air inlet daily.
Lubricate the gearing with SIOUX No. 1232A. The planetary gearing should be greased every 150 hours. The angle bevel
gears should be greased every 8 hours.
Lubricate the angle head every 6-8 working hours with Sioux 1232A grease. The grease fitting is located on the side of the
angle head.
GENERAL OPERATION
• Start the tool by depressing the lever.
• When changing drill bits, make sure the drill is motionless, then press and hold the locking mechanism button located on
the upper housing portion of the angle head.
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
1AM1440, 1AM1441, 1AM1442, 1AM1451, 1AM1452, 1AM1540, 1AM1541, 1AM1542, 1AM1551, 1AM1552, & 1AM1551E
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
June 1, 2006
Murphy, North Carolina, USA
Date and place of issues
(SERIAL "B")
operating this tool.
WARNING
maintenance or service on tool can start unexpectedly.
Tools starting unexpectedly can cause injury.
SOUND AND VIBRATION READINGS
Sound Pressure
Catalog No. dBA
1AM1440 71.3
1AM1441 71.3
1AM1442 71.3
1AM1451 71.3
1AM1452 71.3
1AM1540 71.3
1AM1541 71.3
1AM1542 71.3
1AM1551 71.3
1AM1552 71.3
1AM1551E 71.3
*prt PN8NTC1
DECLARATION OF CONFORMITY
EN 792, EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
Mark S. Pezzoni
President
Power and Specialty Tools
Name and position of issuer
Sound Power Vibration
dBA m/s 2
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
82.7 Less than 2.5
*prt PN8NTC1 *per ISO8662
Signature of issuer
1
Form ZCE491
Date 2006June23/D
Page 1 of 8
Printed In U.S.A.